10521 - Parts

The Shoulder Bolt is a 3/8-16 x 3-5/8 bolt, certified by the original equipment manufacturer. It is a metal bolt which is individually sold and comes in black. Installation requires a wrench or socket and is rated as "Easy" by customers. It is mostly used to keep the wheel in place. It fits onto the unit frame and if broken or removed, th...Read moree wheel will fall off. Refer to your make, model and diagram to ensure this is the correct part.

This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.

This is an Authentic OEM replacement part used on Lawn and Garden Engines. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won\'t start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull th...Read moree starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This Assembly includes a Metal Body Carburetor, Rubber O-Ring and a Gasket. When replacing Carburetor it is advised that you also replace Carburetor Gaskets to ensure proper Air Tight Seal for optimum performance. You will need a Screwdriver to perform this repair.

This is a genuine part which is supplied directly from the original equipment manufacturer and is used with Craftsman lawn mowers. The cylinder head gasket attaches between the engine block and the cylinder head. This part is made head resistant material and is sold individually. For this repair, you will need a screwdriver to remove any ...Read morecovers or shrouds to aid you. Before starting this repair, let the engine cool and disconnect the spark plug wire.

This genuine replacement magneto is designed for Briggs & Stratton engines used in Toro lawn mowers. It plays a vital role in the ignition system by generating the electrical current needed to fire the spark plug. Made from high-quality materials, this part is sold individually. Note: The spark plug boot is sold separately. To replace...Read more the magneto, begin by removing the housing or covers from your mower. Next, remove the spark plug and bind the cylinder to prevent it from turning. Disconnect the ignition wires and remove the old ignition coil. Install the new magneto, carefully setting the correct air gap between the coil and the flywheel. Once installed, reassemble the unit and test for proper operation. A screwdriver set is recommended for this repair.

This is a genuine OEM supplied replacement part designed for use with Briggs and Stratton engines. This float controls fuel flow into the carburetor bowl by adjusting the needle valve. Includes a plastic float and a metal pin. To complete this repair you would need a wrench and pliers.

The O-Ring is a black rubber part, used to provide a seal between two pieces. It can be used in various locations on a variety of equipment. Installation is rate as "Easy" and will require a screw driver, pliers, socket set, and wrench set. If broken, damaged, or worn due to fatigue, you will have a leak and the part must be replaced. Refer to your make, model and diagrams to see if this is the right part for you.

This choke return spring is an OEM direct from Briggs & Stratton. The metal spring is compatible with several small engines. This component works from the choke system, applying the necessary tension to maintain the choke lever position. A screwdriver, wrench and pair of pliers are often required for the repair. The choke return spring is sold individually.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This air cleaner cover is a genuine manufacturer approved replacement part that is specially designed for Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. The purpose of this cover is to secure and protect the air filter element which is sold separately. It is made from durable plastic and it is sold individually. Replacing this part does not require any tools.

This replacement screw is a high quality hardware that is commonly utilized on Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It has multiple applications depending on the unit, please make sure to check appropriate diagrams of your mode for correct location and use of this screw. Note that this hex head scrwe is sold individually.

This OEM-sourced washer in your walk-behind lawnmower provides space and protects the rear wheel from rubbing against the pivot arm assembly, ensuring smooth wheel rotation. A damaged washer may appear worn or cracked, causing the rear wheel to feel misaligned or wobble excessively. If not replaced, it can lead to increased wear and expen...Read moresive repairs. To remove the existing washer, prop up the wheel with a two by four, use a wrench to remove the bolt securing the wheel, slide out the wheel, and then remove the bolt on the rear adjuster to take off the washer. Please note that this washer is sold individually, so make sure to check the quantity needed for your machine before making your purchase.