1050UP537 (1989) MTD Lawn Tractor - Parts

When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near the transmission or the wheels of your machine. If you notice that the machine takes longer to stop or that there is a loud scraping or grindi...Read moreng noise when you push down on the brake, your brake puck may have worn out. If it is not replaced, you risk losing braking power, which leads to equipment damage or accidents. Before any repairs, make sure that your machine is turned off and that the spark plug is disconnected. To dissemble the brake assembly and access the brake puck, use pliers or a wrench to remove any bolts or clips holding it in place. With a screwdriver, pry the brake puck out of your machine. Since this genuine OEM part is sold individually, determine the number of pucks your machine needs by consulting your user manual.

The Hex Flange bearing, .630 inches I.D. is an OEM part. Black in color and made of metal, it is sold individually. It is installed using a wrench or socket and its installation has been rated as Easy by consumers. This part attaches on the worm gear shaft in the cute, and is used to secure the worm gear on the shaft. If broken, you wil...Read morel no longer to be able to control the chute (or you may only have partial control). This breakage can occur due to fatigue over time, and means the part must be replaced. Refer to your owners manual or model number to ensure you are purchasing the correct part.

This authentic OEM hi-pro key, also called a woodruff key or key stock, is a metal component found in your lawn equipment that connects rotating parts. It is 3/16 inch wide and 5/8 inch long. It fits into a specially-shaped slot on a shaft and prevents the parts from moving or slipping out of position while your machine is running. To fin...Read mored and replace a hi-pro key on your machine, check your user guide for instructions. When removing the hi-pro key, insert a flathead screwdriver or needle-nose pliers into its groove and pry it out of its slot. Please bear in mind that this hi-pro key is sold individually.

This special jam nut is sourced directly from the original equipment manufacturer for use with MTD and Ryobi lawn and garden equipment. It is a standard hardware which has multiple applications depending on your tool, please refer to appropriate diagrams for correct location and use of this part. It is made of high-quality metal and it is sold individually.

It is a genuine item that is supplied by the original manufacturer for use with a variety of lawn and garden equipment. A washer is a special part which helps to provide a tight fit between connected components. It is a standard hardware which may have multiple applications. This part provides an identical replacement for a damaged or a m...Read moreissing hardware that was installed on a new unit. Check the diagrams for your specific model for the exact location and the correct application of this flat washer. Note, it is made of durable metal and is sold individually.

This item is an original part from MTD, Ryobi, Yard Machines, Bolens, Yard Man, and Troy-Bilt for use in lawn tractors. The needle bearing attaches to the input shaft. You may need a wrench and a set of pliers when replacing this part. This item might break over time and will need replacing. It is made of metal and is sold individually.

This OEM 5 Pin ignition Switch is a silver, steel, individually sold part. It can be installed using a wrench and screwdriver, and has been rated as Easy to install. The part attaches to the dashboard, and is used to start and shut off the engine. If it is broken (likely due to fatigue), you will no longer be able to start or stop your ...Read moreengine and the part must be replaced. Refer to your owners manual or model number to ensure you are purchasing the correct part.

This is a genuine item that is supplied by the original equipment manufacturer for use with MTD and Ryobi lawn and garden equipment. It is a standard hardware which has multiple applications, please make sure to refer to the diagrams of your model for the correct location and application of this item. Keep in mind it is made of durable metal and is sold individually.

This headlamp is an OEM replacement part manufactured by brands such as MTD, Ryobi, and Yard Machines. It is compatible with over 150 models of lawn tractors. This headlamp provides a light at the front of the machine. With this headlamp, you may operate the machine in the late evening. This part should be replaced if it is burnt out, cracked, or broken. It is sold individually and requires no tools to replace.

This is an original Craftsman replacement part. The carriage screw is designed by the manufacturer for use in snowblowers and lawn tractors. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws used in the machine. Refer to the parts diagr...Read moream to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with trimmers and lawnmowers from Ryobi and MTD. The metal nut is used with different types of machines and the application of the nut can vary based on the model of the equipment. It is recommended to verify the part\\\'s compatibility a...Read morend usage by reviewing your model\\\'s diagram. This nut is available as an individual replacement part. A hex socket wrench and a driver are needed when installing this part.