10431-2 General Electric Range - Instructions

We took out the philips screws on the right and left side of inside of the oven and two hex head screws on the clip on the top of the oven in the front. Then using a slot screw driver pryed the oven liner out enough to remove old gasket and replace the new gasket. We did see in some online directions that we were suppose to remove enti ... Read more re oven from cabinet and loosen bolts in the back. But, we were able to get enough space to get the old gasket out and new one installed. We did use a 1/4" thick piece of wood on face of oven to prevent any denting of oven when prying out the liner of the oven.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

After several temporary fixes, one of the end caps finally broke completely, so the handle fell off. Ordered both caps, they arrived remarkably fast, and were installed easily.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Took oven door off. Removed screws that were holding oven insert. Pulled out oven insert. Removed old gasket. Installed new gasket. Push oven insert back. Installed screws. Replaced oven door.

Son-in-law unscrewed oven compartment; broken gasket was easy enough to remove and new gasket easy to replace; only problem was oven door would not shut tight. Tried shoving gasket harder into groove, tried turning on oven and heating new gasket to see if it would soften. Finally got it to close by pushing hard on left side of oven and ... Read more inside light would at least go off and stay off.

the first end cap broke when I tried to tighten the screws, the end cap holes were too small, Thirty some dollars down the drain. Drilled out the second end cap before I tighten the screws, worked fine. Make sure you drill out the holes of the end caps or they will split out and you lose your money. There are no warnings about this proble ... Read more m.

I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.

I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!

Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.

replaced lights in refrigirator and freezer

Removed torx head screws. Removed broken pieces of the end caps. Replaced the handle installed the end cap screws.

The parts were shipped quickly and were what I ordered. The one suggestion I would make to the installer would be to drill out the insert holes a bit in the plastic columns in the inside of the bracket. There are two such columns and they are used to provide further strength to the end cap. However, the diameter of the screw is too large ... Read more for the insert hole because as I installed the first bracket one of these columns broke. After drilling out the insert hole, the screws were still snug and the end cap (and door handle) was quite solid.

Repair went a lot faster and easier than I anticipated. Instructions are similar to those posted by others.
1. Verify that new gasket looks mostly like old gasket as best you can since not all of old gasket is visible.
2. Shut off circuit to oven (optional, but good practice)
3. Remove racks, trays, etc from oven to red ... Read more uce weight at Step 7
4. Remove oven door by partially opening door to broiler position (about 20 degrees). Door should catch and stay open on its own. Slide up and lift off door. The “hinges” are spring loaded so carefully return them to closed position so they won’t snap shut on fingers.
5. Remove Phillips screws, one on each side wall of oven liner.
6. Remove two hex screws and metal gasket-holder on top center of oven liner.
7. Pull and slide oven liner out of oven mainframe about 1/4 “ to 3/8”. This may be the most difficult part of the job.
8. If possible to remove just a couple of inches of one bottom of old gasket (right side is easiest), verify that the cross-section profile of both old and new gaskets are essentially the same. If not, you have the wrong gasket.
9. Pull and remove old gasket. If gasket is dry and cracking, it may be necessary to scrape it out with putty knife, flat-blade screwdriver, etc. if it has fused to metal over the years. Note how it was installed on the metal edge of the oven liner.
10. Locate the mid-point on the new gasket length and begin inserting it at the top-center of the oven liner where you removed the two hex screws. Continue installing along both left and right sides of the liner. Each end of the gasket should extend to just above the respective hinge. No trimming should be necessary. Ensure a snug fit all along each side and top.
11. Push liner back into oven mainframe. Replace Phillips screws, gasket-holder, and hex screws.
11. Pull out each hinge to broiler position.
12. Replace door by sliding down onto hinges. Close door and check for tight fit against gaskets. Gaskets will flatten somewhat over time
13. Restore power, racks, trays, etc.

Took out the old & put in the new one-Done!