10421 - Instructions

1st I opened the oven door and removed the 2 screws that hold the outside and inside of the door together. With the door separated I removed the 2 screws that hold the end caps in place, then removed the old end caps. I put the new end caps on the oven door handle, aligned the holes for the end cap screws and reinstalled the screws,then ... Read more reinstalled the oven door screws,closed the oven door and started cooking.

We took out the philips screws on the right and left side of inside of the oven and two hex head screws on the clip on the top of the oven in the front. Then using a slot screw driver pryed the oven liner out enough to remove old gasket and replace the new gasket. We did see in some online directions that we were suppose to remove enti ... Read more re oven from cabinet and loosen bolts in the back. But, we were able to get enough space to get the old gasket out and new one installed. We did use a 1/4" thick piece of wood on face of oven to prevent any denting of oven when prying out the liner of the oven.

Also replaced fuel tank , the built in fuel shut off started leaking , had to replace the tank. Ordered a new one Briggs & Stratton original equipment fit perfect . This is a 25 year old Briggs & Stratton lawn mower 3.5 HP, Runs perfect, starts by the 2nd crank every time. First time I ever had to spend money on it since I bought it new i ... Read more n 1991

After several temporary fixes, one of the end caps finally broke completely, so the handle fell off. Ordered both caps, they arrived remarkably fast, and were installed easily.

Took oven door off. Removed screws that were holding oven insert. Pulled out oven insert. Removed old gasket. Installed new gasket. Push oven insert back. Installed screws. Replaced oven door.

Removed oven door from oven. Removed the inner oven door portion from the outer part to gain access to inner screws attaching end caps to front of stove door. Removed those screws and the old end caps & broken off pieces. Pressed oven door handle bar into new end caps. Reattached oven door handle assembly to front of oven door. Reinstalle ... Read more d inner oven door which included long screws that also went into the new end caps. Reinstalled oven door on oven. Job was easy. Price was certainly right for the end caps at $10.01/each.

Son-in-law unscrewed oven compartment; broken gasket was easy enough to remove and new gasket easy to replace; only problem was oven door would not shut tight. Tried shoving gasket harder into groove, tried turning on oven and heating new gasket to see if it would soften. Finally got it to close by pushing hard on left side of oven and ... Read more inside light would at least go off and stay off.

First I unscrewed the end of the oven door and realized I could replaced the parts easily that hold the handle on the door. Then I held the sharp, broken plastic ends with a towel and used my drill with a thingy that fits on a small hex nut and unscrewed the broken handle parts and removed them. All I had to do after that is screw on t ... Read more he new handle holders with the handle bar fit snuggly between them, presto, new handle bar installed. Great service from partselect. com. Would use them again.!

I read the previous repair stories and figured it couldn't be that tough. Mine actually had a slight deviation and I'm sure based on model...
To remove the oven door handle, I had to remove 3 screws (phillips) on the top of the hinged door. This allowed the face plate to easily pull away from the inside of the door. The existing hand ... Read more les were held in place by a single hex head screw each.
Voila, in 2 minutes the entire handle was off.
This is where things had a slight deviation.
The door end caps I bought had 2 alignment prongs that extended beyond the actual surface. My door did not have holes for them to go into. No big deal, I took some wire snippers and clipped the little plastic prongs off so it was flush like my old ones. That took about 3 minutes because I had to go back into the garage to get the tool :-)
My metal door handle bar did not want to go all the way in very easily into the end caps. I went back into the garage and got some WD40 and sprayed into all pieces and wiggled things back and forth for a few minutes, placing it against the oven a couple of times to ensure I had the bar was seated enough where the holes lined up with the oven.
I would recommend putting the end caps on the bar PRIOR to attaching one side to the oven. I originally did not do this and when it was difficult to get the bar on, I had to take it off so I could perform the procedure I just mentioned.
Honestly, the entire "job" took 10 minutes.

the first end cap broke when I tried to tighten the screws, the end cap holes were too small, Thirty some dollars down the drain. Drilled out the second end cap before I tighten the screws, worked fine. Make sure you drill out the holes of the end caps or they will split out and you lose your money. There are no warnings about this proble ... Read more m.

Although the parts did fit, some modification was needed to remove the excess tabs as it appears these parts were for multiple applications. However the end result was a good fit and reapirs were successful.

Prices on drip pans were so reasonable I easily replaced them . No screws involved here. For end cap, had to remove both screws that held porcelin inner door wall to get to one other screw that held broken handle on outside of door. Put same screw into new end cap. Closed inner porcelin liner. Those two longer screws go through both p ... Read more anels and screw into end cap (one for each end cap) There are two screws in each end cap. This saved me so much money and is the 2nd appliance I have fixed myself. 60 year old female. The other was my dishwasher. This site is a blessing.

Had to take back off of the door to get to screw that held the broken piece of handle before installing the new part. Then had to put the back on the door and slip the door into place.

I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!

I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.