1041 - Instructions

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the ... Read more tab. It was sooo easy once I found that. I repeated in on the other side.

This could not have gone easier! As long as you get the proper parts it's a piece of cake. I wish everything was this easy!

Installed New rollers onto bottom rack. Part order & delivery were top notch from Partselect. Will definitely order from them again.

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for ... Read more having the parts I needed as Sears had discontinued them for this Kenmore appliance.

merely snapped the part on

Fisrt, I opened dishwasher door. I then pulled out the lower rack & put new part in place and pushed in lower rack. Last, I closed dishwasher door.

I ordered a new door gasket and door spring. I unscrewed the two screws that hold the dishwasher in place and pulled it out. I pulled the old broken spring off with pliers and installed the new one ,,,very easy. I then took the new door gasket and soaked it in hot water in the sink for 15 min. That made it very soft and pliable to work wi ... Read more th. I used pliers to pull the old gasket out then cleaned the area around the old gasket where crud had built up. I pushed in the new gasket working from top to bottom one side at a time. Turned it on an ran through a cycle and it works perfect now ,,,no leaks.

Rollers just snapped on the diswasher rack. Took just seconds to do.

first I removed the 4 screws holding the cover in place. then I removed the 26" flourescent tube by slowing twisting it free. Then I attemped to buy another one at 6 or 8 stores with no luck. While surfing the web for tappan range replacement bulbs, your web site popped up. Thank god.

The repair did not happen. The item number PS9294414 was the wrong
part. When I looked up the model number of 126-T02-0625-B1 engine after I tried to install it. The PartSelect answer was that they no longer had parts for 126-T02-0625-B1 engine any more. Do I need to send the
Spring-Choke Return and get my refund back. If so h ... Read more ow do I do it.

Ordered the new roller assembly and in no time the upper rack was back together, up and running. Now to see about replacing the other two rollers and the side rails as they are showing wear and tear.

Thanks for the quick ship.

I only had one break, but bought both to replace. I don't agree with those that say you have to slide the dishwasher out to repair. I simply removed the lower kick plate, and replace the springs in no time. Very easy as was ordering the parts. I will return here for all my appliance parts in the future. Hope I don't actually need any.

Simply remove the bottom panel below the door. The owners manual (22 year old model) showed the proper hole in which to attach the spring. Attach spring to door and then to frame of dishwasher, as illustrated in manual. It is a tight fit to get your hands in there, but once you do it is a snap. We have replace these springs several t ... Read more imes over the life of this appliance, this is the first time we have actually found the proper springs, should last a long time. Thank you Parts Select for having the inventory for such an old model!

This dishwasher has a plastic bolt that holds the actuator on. The action loosens the bolt and it wobbles and eventually comes off. After enough attempts the bolt will strip and need to be replaced. I took some 3M loctite this time to hold it in place. It is 24 years old, but still kicking

Removed lower panel; unmounted fill valve assembly. Installed two springs. Remounted fill valve assembly and reinstaslled the lower panel. Door must be in a near closed position to gain access to the door "L" spring brackets.