All Installation Instructions for Kenmore Range 1037447002

The auger in the ice bucket was rusted

Frank from Temecula, CA
Really Easy
Less than 15 mins
Screw drivers

Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .

Was this helpful?

rusty auger tainting ice

JoAnn from Argyle, TX
Really Easy
Less than 15 mins
Screw drivers

It was so easy! I seldom attempt any household repair because I have a husband that can fix anything, but he was not available. One screwdriver & remove 4 screws attaching the existing front to old auger/bucket. Line up the screw holes on new bucket with old front, put the 4 screws in through those holes tighten screws & I was done.

Was this helpful?

auger and bucket neded to be changed because of rust which caused the auger and other metal parts to rust which created an unpleasant odor in ice and freezer. to

Joan from Colleyville, TX
Really Easy
Less than 15 mins
Screw drivers

The part arrived promptly but was defective. Upon learning of the problem by PartSelect a new part was shipped and was delivered incredibly quickly. Installing it was easy and took only about 5 minutes. We were pleased with the speed in sending the parts and the ease of installation. We will call on them again if necessary because of ... Read more

Read less

Was this helpful?

Ice crusher was broken, putting plastic in ice.

Joe F. from Kountze, TX
Really Easy
Less than 15 mins
Screw drivers

Ordered Auger and Ice Bucket Assembly All I had to do was install 4 screws. Worked great. Thanks.Joe

Was this helpful?

old ice maker was rusty had not been using it

Wilbur from Brazoria, TX
Really Easy
15 - 30 mins
Screw drivers

order new augerand ice bucked changed face plate 4 screws now have good clean ice

Was this helpful?

Replace Auger And Ice Assembly

GUSTAVO from CORONA, CA
Really Easy
Less than 15 mins

Just replaced the auger from the old one

Was this helpful?

The silver plating on the auger was coming loose, rusting and getting in the ice cubes.

Terry from Cocoa Beach, FL
Really Easy
Less than 15 mins
Screw drivers

All I had to do was remove four (4) screws from the old ice bucket assembly to remove the front cover and attach it with the existing screws to the new ice bucket assembly. It was a very simple repair. Thanks for the expedient delivery and the exact replacement part that I needed.

Was this helpful?

The Ice Bucket had rusted

Leticia from El Paso, TX
Really Easy
Less than 15 mins
Screw drivers

It was really simple, remove 4 screws form the old cover and put it on the new bucket. Simple, Simple!!

Was this helpful?

Auger and Ice Bucket for GE side by side was rusty

Jay from Jacksonville, FL
Really Easy
Less than 15 mins
Screw drivers

followed the previous posts, loosened four screws on the front panel, attached panel to new auger and ice bucket, and was good to go. Excellent advice!

Was this helpful?

Ice bucket assembly broke

William from Collierville, TN
Really Easy
Less than 15 mins
Screw drivers

Ice bucket and auger came fully assembled. Just had to attach the face plate from the broken ice bucket assembly and slide it into the freezer. There were only four Phillips screws involved.

Was this helpful?

Bucket was broken at the back where the auger turns.

Ernest from Plano, TX
Really Easy
Less than 15 mins
Screw drivers

Removed the bucket assembly from the freezer. Remove the four screws holding the front cover on the bucket. They are on the backside of the front cover. Installed the old front cover on the new ice bucket with the four screws.

Was this helpful?

no water to ice maker or water dispencer

craig from sweeny, TX
Really Easy
30 - 60 mins
Pliers, Screw drivers

replaced circuit board and water solenoids

Was this helpful?

1037447002 Kenmore Range - Instructions