10313 - Overview

This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.

The Stepped Washer is used to secure the wheels onto the shaft of a push mower. It attaches to the wheel axle. If broken due to wear/fatigue, the wheel will come off and the part should be replaced. Installation is rated as "Easy" by customers and will require a socket set. This part is individually sold, gray, and constructed of metal. R...Read moreefer to your make, model and diagrams to check if this is the right part for you.

This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually. Over time, you may notice that you are having trouble retracting your pull cord, which could be a symptom of the rewind starter spring f...Read moreailing due to fatigue or wear. Replacing this part is a repair our customers found easy. Locate and replace the start spring inside the starter housing; no special tools are required for this job.

This OEM Locking Ring holds components or assemblies onto a shaft or in a housing/bore when installed in a groove. Installation is rated as "Easy" by customers and will require pliers. The part secures the drive pinion gear to the drive shaft, and if broken due to wear/fatigue/damage, it will need to be replaced.

Hard starting may come from the recoil system instead of the carburetor or spark plug. If the rope pulls but the engine does not turn, the starter clutch may be worn, dirty, or jammed. The clutch turns the crankshaft during starting and lets go when the engine runs. First inspect the rope, rewind spring, pulley, flywheel screen, and clutc...Read moreh bearing. Confirm fit with the complete engine number. Remove the spark plug wire, wait for hot parts to cool, and keep dirt out of the bearing area. Test free movement before putting the shroud back on.

This is an authentic manufacturer sourced replacement part designed for use with a variety of lawn and garden equipment. This carburetor intake gasket which provides an air tight seal for the carburetor. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

This is a high quality replacement hardware that is specially manufactured for use on Toro lawn and garden equipment. Two of these screws are generally used to secure the belt guide to the mower deck. Please note this durable metal hex head taptite screw is included per order.

The Breather Gasket is OEM and used to provide an airtight seal for the breather assembly. It is a gray part, attached between the breather cap and engine. Installation is rated "Easy" and will require a wrench set and socket set. If broken, damaged, or worn due to fatigue, there may be oil leaking from it, and the engine may be running r...Read moreough from an unwanted vacuum sucking in air. If this happens, replace the part. Refer to your make, model and diagrams to ensure this is the correct part for you.

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This OEM engine screw is a genuine Briggs & Stratton replacement fastener designed for secure, vibration-resistant attachment of engine components in small gasoline engines and outdoor power equipment. Manufactured to exact factory specifications, it provides proper thread engagement and clamping force to help prevent loosening, reduce vi...Read morebration, and maintain long-term engine reliability under operating stress. Built with durable, corrosion-resistant materials for extended service life, it is an ideal replacement when original screws are missing, stripped, or worn, helping ensure safe assembly, consistent performance, and proper engine operation.

This OEM-sourced washer in your walk-behind lawnmower provides space and protects the rear wheel from rubbing against the pivot arm assembly, ensuring smooth wheel rotation. A damaged washer may appear worn or cracked, causing the rear wheel to feel misaligned or wobble excessively. If not replaced, it can lead to increased wear and expen...Read moresive repairs. To remove the existing washer, prop up the wheel with a two by four, use a wrench to remove the bolt securing the wheel, slide out the wheel, and then remove the bolt on the rear adjuster to take off the washer. Please note that this washer is sold individually, so make sure to check the quantity needed for your machine before making your purchase.

This is a genuine OEM sourced part which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardwa...Read morere. Keep in mind this high-quality item is made of durable metal and is sold individually.