09860-0 Briggs and Stratton Generator - Parts

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

It is a genuine item that is supplied by the original equipment manufacturer for use with Generac portable generators. This is an identical replacement for a missing or damaged air cleaner cover, please note the housing and the element are both sold separately. It is a high-quality component which is made of durable plastic and is sold individually.

A carburetor controls how much fuel and air reach a portable generators engine. Varnish, corrosion, a sticking float, or a worn needle can make the engine hunt, run unevenly, stop under load, or refuse to start. A complete replacement assembly may be useful when cleaning and basic service do not correct the fault. Compare the mounting pat...Read moretern, throttle and choke linkages, fuel connection, and full engine code before ordering. New mounting gaskets may need to be purchased separately. Shut off the fuel, disconnect the battery and spark plug, and label every connection. After installation, check for leaks and confirm stable speed and output under the recommended test load.

This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The most common reasons for replacing the grommet is if the fuel is leaking from the fuel tank, the fuel lines are loose at the tank or the rubbe...Read morer grommet is cracked and not sealing. This part is made out of rubber and is sold individually. Here is a list of tools that are needed to replace the grommet a receptacle for draining fuel, a wire hook (to retrieve fuel lines), screwdriver, wire cutters or scissors.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This is an authentic OEM component from Briggs & Stratton. The oil drain plug is made for use with many small engines. The metal plug is often fastened into the crankcase cover, and is removed to drain the oil as needed. A hex key or Allen wrench is necessary for the removal and replacement. The oil drain plug is sold individually.

This authentic manufacturer-supplied part is made for use with Generac portable generators. It is the spring that connects to the governor control rod. This is an identical replacement for a missing or a faulty hardware that was installed on a new unit. Make sure to check the appropriate diagrams of your specific model for the exact locat...Read moreion and the correct installation of this component. Note, one durable metal spring is included.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

This is a genuine OEM supplied part that is specially designed for Briggs and Stratton portable generators. The item provides an identical replacement for a faulty or a missing power regulator assembly that was installed on a new unit. It is made of high-quality materials and is sold as an individual item. Refer to the owner's manual and the appropriate diagrams for your model to ensure the correct repair procedure.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton generators and pressure washers. The purpose of this component is to reduce the vibration of a working unit, unfortunately, over time it may begin to fail eventually requiring a replacement. Please make sure to refer to...Read more the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality vibe mount with a washer is sold individually.

The battery charge rectifier goes inside the control box. It is an OEM from Briggs & Stratton for use in generators. This part is sold individually and is made of metal. A wrench and a screwdriver may be required to replace this part. It will need to be replaced if it breaks.