0941 Generator - Overview

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

The OEM vibration mount is a black rubber part, which is used to prevent vibrations between the frame of the generator and the floor. It can be installed with a screw driver,and its installation is rated as "Easy" by customers. It is installed on the bottom of the frame, facing the ground. If broken due to general wear/fatigue, there will...Read more be a noticeable vibration and the part may be tilted to one side. If this happens, the part should be replaced. Refer to your model, make and diagram in order to ensure this is the correct part.

This is an authentic OEM sourced part which is specially made for DeWALT planers. It functions as a safety device. When the circuit becomes overloaded, this circuit breaker switch interrupts the transfer of electricity to the motor. Flip the switch on the circuit breaker to reset the connection. Please make sure to refer to the appropriat...Read moree diagrams for your model for the correct location and application of this component. Keep in mind this high-quality circuit breaker is sold as an individual item.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

The battery charge rectifier goes inside the control box. It is an OEM from Briggs & Stratton for use in generators. This part is sold individually and is made of metal. A wrench and a screwdriver may be required to replace this part. It will need to be replaced if it breaks.

This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It is a replacement part directly sourced from the manufacturer for use in generators made by Briggs & Stratton and Snapper.

This is an original replacement part sourced directly from the manufacturer. The rocker arm is found in Generac generators. This part is made of metal, and is attached to the push rod guide plate in the head guide and seat assembly. You may require a screwdriver or Allen wrench when replacing this product. This item is sold as an individual replacement part.

This is a genuine OEM sourced component that is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is designed to keep the fuel in the tank. It provides an identical replacement for a missing or a faulty part that was installed on a new unit. Please make sure to check the approp...Read moreriate diagrams of your model for the correct location and application of this cap. Keep in mind this high-quality part is made of durable plastic and is sold individually.

NULL