0909 - Overview

This driven ring is an OEM part direct from Snapper. The flexible plastic ring is compatible with many lawn mowers. This item is often fitted between the driven disc assembly and ring retaining plate, assisting the drive disc with propelling the mower. A screwdriver, wrench set, pliers are needed for the repair. This item is sold individually.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking at the connection between the bottom of the oil fill tube and the crankcase. This item also allows the fill tube to firmly sit into the case. The dipstick tube seal if available as an individual replacement part.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This is an authentic replacement part manufactured for use with small engines. This oil seal keeps oil inside the crankcase, and seals the shaft. It is recommended to replace the crankcase gasket when servicing the case, the gasket is available separately. The oil seal is sold individually.

This manufacturer approved replacement part is specially produced for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is utilized to keep the oil in the tank. Please note this durable plastic oil fill cap is sold individually.

This is an authentic manufacturer made replacement part which is specially designed for use with Craftsman lawn mowers. The engine crankcase gasket seals the crankcase cover and to keep out dirt and debris from compromising the engines components. This part is sold individually though it is a common wear part, so we do recommend ordering ...Read morea spare. For installation, you will need a screwdriver to remove any covers and shrouds and a socket wrench to aid you.

This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special oil seal is commonly used to form a seal between the camshaft and the crankcase cover. The oil seal is available as an individual replacement part, please see model diagram for associative parts.

This is an authentic OEM component from Briggs & Stratton. The oil drain plug is made for use with many small engines. The metal plug is often fastened into the crankcase cover, and is removed to drain the oil as needed. A hex key or Allen wrench is necessary for the removal and replacement. The oil drain plug is sold individually.