0902 - Parts

This durable nylon starter rope is an authentic OEM supplied replacement part that is specially produced for use with Briggs and Stratton engines that are commonly installed on Toro lawn and garden equipment. When the rope is pulled to start the engine, it is returned back into the starter pulley by means of the starter spring. One starte...Read morer rope is included per order, please note the handle grip and other parts are all sold separately.

This is a Briggs & Stratton and Toro replacement part directly sourced from the manufacturer for use in engines, generators, tillers, blower-vacuums, and lawn mowers. The breather assembly is made of metal and helps to vent the air from the engine. It might require a socket set, a set of pliers, and a screwdriver to replace this part if i...Read moret becomes broken. The part is sold individually but also includes the gasket-breather.

This is a genuine replacement part that has been sourced from the original manufacturer to be used with snow thrower engines from Husqvarna and Toro. The metal screw is used to fasten the fuel tank to the tank mounting bracket. This item is available as an individual replacement part, please note a hex socket wrench may be needed to install this item.

This is a genuine manufacturer-sourced component which is specially produced for Briggs and Stratton engines commonly installed on lawn and garden equipment. It is a standard hardware that is generally utilized to secure the debris screen guard, please make sure to refer to the appropriate diagrams of your model for the correct location a...Read morend use of this screw. Keep in mind it is a high-quality component which is made of durable metal and is sold individually.

Gear worm

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This manufacturer approved replacement part is specially produced for use with Briggs and Stratton engines commonly installed on Toro lawn and garden equipment. It is utilized to keep the oil in the tank. Please note this durable plastic oil fill cap is sold individually.

This governor spring is an OEM direct from Briggs & Stratton. Made for use with many small engines, this metal component provides the necessary tension to the governor. Refer to the diagrams of your specific model for the correct installation of this hardware. This item is sold individually. You may need a screwdriver to replace the old part.

This is an authentic manufacturer made replacement part which is specially designed for use with Craftsman lawn mowers. The engine crankcase gasket seals the crankcase cover and to keep out dirt and debris from compromising the engines components. This part is sold individually though it is a common wear part, so we do recommend ordering ...Read morea spare. For installation, you will need a screwdriver to remove any covers and shrouds and a socket wrench to aid you.

This is sold as a set that contains three rings. The rings attach to the piston and help to create a seal. When replacing these parts a screwdriver, a set of pliers, and a socket set might all be required during the installation process. These parts are made out of metal and will need to be replaced if they break or bend. They are authent...Read moreic Briggs & Stratton and Toro replacement parts that are sourced from the original manufacturer for use with engines, generators, tillers, and blower-vacuums.

This spark plug terminal is supplied directly from the original equipment manufacturer. The metal terminal is designed to fasten the spark plug to the engine lead wire. This component is sold individually, and needle nose pliers are helpful with the repair. Please refer to the appropriate diagrams of your engine model for the proper application of this hardware.

This is a genuine item that is supplied by the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or faulty spacer that helps to separate components and provide a tight seal between them. Please make sure to refer to the app...Read moreropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber and is sold individually.