083- MTD - Parts

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

The Throttle Box Assembly, or the Throttle Assembly, is a kit that includes the housing, handle, and hardware. It is black and constructed of steel and plastic. It can be installed onto the right hand upper handle, using a screwdriver and pliers, and is rated as Medium difficulty to install. This kit contains the parts that control the ...Read moreamount of the air and fuel entering the engine. When the part breaks (likely due to fatigue) you will no longer be able to control the engine. If nothing happens when you move the handle, that means it has become disconnected. When the part is broken it must be replaced. Check your model number to ensure you are selecting the correct replacement part.

The Lever and Knob Assembly (or Front Wheel Height Adjuster) is used to adjust the front height of the mower, and attaches on the front wheels. It can be installed using a socket set and wrench set, and is rated as "easy" to install by our customers. If broken or damaged (likely due to general wear over time) you will no longer be able to...Read more move it to make adjustments, and the part should be replaced. This black, plastic part is sold individually. Refer to your make, model and diagrams to ensure this part fits your machine.

The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.

Made of durable silver plastic, this Flange Bearing is an authentic manufacturer-source replacement part for hundreds of models of lawn and garden equipment. It is used to allow a shaft to connect while moving smoothly and freely and is sold individually. When this part malfunctions, you may notice the shaft becomes very sloppy or comes...Read more disconnected. To complete this repair, you will need a screwdriver, a socket set, and pliers. Customers rate this repair as Medium difficulty.

This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move. If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This is a genuine OEM sourced part that is not part of a kit or assembly and is sold individually. This Spring Extension, or Extension Spring, serves a variety of purposes, depending on your model. It is black, made of metal, and may be found in multiple locations on your machine. This part needs to be replaced when it is worn, weak, dam...Read moreaged, or broken. Depending on its purpose, you may no longer have control of your machine when the spring breaks. You will need pliers to complete this repair. Customers rate this repair as Easy.

This genuine OEM carriage bolt is used to secure various parts in lawn and garden outdoor equipment. The bolt has a round head with a square area underneath it that prevents the bolt from turning and coming loose when it is installed. The bolt shaft has a diameter of 5/16 inches, with 18 threads per inch and the threaded portion of the bo...Read morelt is 0.62 inches long. If the bolt is corroded, the threads are worn down, or the head is damaged or deformed, you will need to replace the bolt to keep your equipment parts secured and functioning efficiently. To replace the bolt, first remove the nut using a wrench or socket. Once the nut is removed, you can unthread the bolt. Insert the new bolt in position, thread the nut on and use a wrench to tighten it. Be careful not to overtighten the bolt to avoid damaging it or stripping the threads. This carriage bolt is sold individually.

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This ball joint connects moving parts in the steering or control linkage of select lawn tractors and snow blowers. It has 3/8-24 male and female right-hand threads. The male threaded end is shorter than a standard joint. Use the complete equipment model and serial number to guarantee the proper fit. Replace the joint if it is loose, bent,...Read more rusted, or hard to move. Before removal, measure the linkage or count the exposed threads so the new joint can be installed in the same position.