06-427512 (1990) MTD Lawn Mower - Parts

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

The Lever and Knob Assembly (or Front Wheel Height Adjuster) is used to adjust the front height of the mower, and attaches on the front wheels. It can be installed using a socket set and wrench set, and is rated as "easy" to install by our customers. If broken or damaged (likely due to general wear over time) you will no longer be able to...Read more move it to make adjustments, and the part should be replaced. This black, plastic part is sold individually. Refer to your make, model and diagrams to ensure this part fits your machine.

The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.

This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move. If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

This is an authentic MTD tiller replacement part. The hex B-tap screw is used to fasten the cable barrel holder to the clutch lever to ensure good tension on the clutch cable. The part is made of durable metal. You will need a wrench to replace this piece. This item is sold individually.

This Bell-Wash Flat Washer is an OEM part that measures .40 inches I.D. x 88 inches O.D. This washer is a silver, metal, washer sold individually. This part is rated as Easy to install by customers. If missing or damaged (likely due to fatigue) it should be replaced. Refer to your owners manual to ensure this is the correct part for you.

This item is a genuine OEM sourced replacement part that is intended to be used with riding lawnmowers from Cub Cadet, Yard Machines, Troy-Bilt, Bolens, and Yard-Man. The clip is used to attach the trail-shield to the back of the mower\\\'s deck. The hinge clip is sold as an individual replacement part, please note two clips may be needed.

It is an authentic OEM sourced replacement part which is specially designed for use with walk-behind lawn mowers. This cable is connected to the control handle that is pressed down while running the lawnmower, over time it may wear out or get damaged eventually requiring a replacement. Keep in mind this high-quality rubber insulated compo...Read morenent which is sold individually. Make sure to refer to the appropriate diagrams of your specific model for the correct location and application of this item.

This is an authentic replacement part that has been sourced from the original manufacturer to be used with trimmers and lawnmowers from Ryobi and MTD. The metal nut is used with different types of machines and the application of the nut can vary based on the model of the equipment. It is recommended to verify the part\\\'s compatibility a...Read morend usage by reviewing your model\\\'s diagram. This nut is available as an individual replacement part. A hex socket wrench and a driver are needed when installing this part.