0500 - Parts

This screw is sold individually.

Sold individually.

This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave will not heat properly, will not turn on, or the touch pad becomes unresponsive, there could be a faulty fuse which should be replaced. Remem...Read moreber, since this part contains an electrical charge, before you replace the fuse from your microwave, make sure that the power is disconnected from the unit. This part is sold individually. NOTE: Make sure your microwave is unplugged, and your capacitor is discharged before you begin this repair. A capacitor stores large amounts of electricity even after your microwave is unplugged.

This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.

This part is sold individually. This nut can be found in various appliances including a dishwasher, air conditioner, washer, dryer, range/cooktop, oven, freezer, range hood, and refrigerator. There is a serrated pattern along the edge of the nut, which helps to avoid loosening while the appliance is in motion. Nuts may corrode or rust ove...Read morer time and will need to be replaced. You will need a wrench to screw the nut into place. This genuine OEM part comes directly from the manufacturer.

This suction tube is compatible with various makes and models of airless paint sprayers and is sold as an individual OEM part. It draws paint from the container/reservoir and delivers it to the sprayer for application. This tube has a built-in filter attached, to prevent dust, dirt, or debris from entering the sprayer system. When suction...Read more tubes become clogged/blocked, damaged, or lose their suction, they can become inoperable and will lose any and all function. It is recommended that you regularly inspect the tube for damage or clogs, and if you notice your sprayer leaking from connection points around the tube or inconsistent spray patterns and suction ability, the tube is likely needing replacement. To replace this tube within your paint sprayer assembly, disconnect your sprayer from power and relieve the pressure within the sprayer. Drain all paint from the sprayer and paint reservoir to avoid mess. Remove the old suction tube by unscrewing it and/or any securing hardware, and then install the new tube with the same process as before. With the new tube installed, perform a test run with the sprayer to ensure the suction tube works properly before using it normally.

This fuel filter bowl is an OEM direct from Briggs & Stratton. Compatible with many small engines, this plastic item is fitted with the fuel shut-off valve. No tools should be required for the replacement. The fuel filter bowl helps to separate water from the fuel, and is sold individually. The fuel filter bowl is sold individually.

It is an authentic OEM sourced part which is specially made for use with Briggs and Stratton engines commonly installed on a variety of lawn and garden equipment. This is an identical replacement for a faulty or a missing spark plug wrench that was included with a new unit. The wrench allows a user to secure or remove a spark plug. Refer ...Read moreto the appropriate diagrams for your model to ensure the exact location and the correct application of this component. A screwdriver will be needed to secure or remove this part. This high-quality part is made of durable metal and is sold as an individual item. Note. This spark plug wrench fits 5/8" and 13/16" spark plugs.

The control knob is part of the speed control panel. This item is made of plastic and is sold individually. It is an authentic OEM sourced item which is specifically produced for use with blowers, engines, generators, and vacuums made by Briggs & Stratton and Toro. It may require a set of pliers during installation. This part may become broken and will need to be replaced.

This is a genuine item that is supplied by the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or faulty fuel strainer that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of ...Read morethis component. The part helps to keep any contaminants from going into the engine. Keep in mind this high-quality item is made of durable metal and is sold individually.