03025 Generator - Overview

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.

The OEM voltage regulator or voltage control is a part used to regulate the voltage so it can provide the right amount of power to electrical components. It attaches inside the alternator housing. The part is black and 2 x 3.5 inches. If damaged, the voltage will become too low/high and the part should be replaced. This part requires a vo...Read moreltmeter to use properly. Please refer to your make, model, and diagram to ensure this is the correct part.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This wheel is an authentic replacement part sourced directly from Briggs and Stratton. It is customarily used for portable generators. The purpose of this wheel is to reduce the amount of effort needed to transport the generator. This part is made of rubber and only includes one wheel. Please note the machine requires two.

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

This item is an authentic Briggs & Stratton replacement part that has been sourced to be used with portable generators. The metal valve is used to connect the fuel line to the fuel tank and to control the flow of fuel from the tank. This item is available as an individual replacement part.

This handle fastening kit includes two plastic thread wingnuts and two carriage bolts, which are essential for securely attaching the handle assembly to your pressure washer. The handle assembly is typically located where the handle connects to the main body of your machine. When these parts are broken, the handle will feel wobbly or loos...Read moree, and there may be visible damage to the mechanism. It is crucial to fix the assembly promptly, as a loose handle can pose safety risks and make it difficult to operate the pressure washer effectively. Please note that this genuine OEM kit is sold individually, and the handle itself is not included.

This is an authentic Briggs & Stratton replacement part that is intended to be used with portable generators. The valve is used to connect the fuel line to the tank and to control the flow of fuel from the tank. This item is available as an individual replacement part.

The OEM E-Ring is a silver metal part used to secure the wheel on the shaft. If broken, the wheel may fall off, and the part must be replaced. It is rated as "Easy" to install and requires pliers and a screw driver.