030253-0 Briggs and Stratton Generator - Overview
Sections of the 030253-0
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
$27.33
In Stock
Breaker, Circuit, 20a
PartSelect #: PS9919917
Manufacturer #: 209872GS
This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the elec...
$15.46
In Stock
Brush Holder Assembly
PartSelect #: PS9157810
Manufacturer #: 91825GS
This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon b...
No Longer Available
Kit, Handle Fastening
PartSelect #: PS9181264
Manufacturer #: B2203GS
This handle fastening kit includes two plastic thread wingnuts and two carriage bolts, which are essential for securely attaching the handle assembly to your pressure washer. The handle assembly is ty...
$8.11
In Stock
Cap, Fuel Gauge
PartSelect #: PS8903364
Manufacturer #: 189420GS
This fuel gauge cap is a genuine manufacturer-approved replacement part sourced directly from Briggs and Stratton. It is commonly used in portable generators to determine the amount of fuel left in th...
No Longer Available
Cover, Rbc Plastic With Cap
PartSelect #: PS8909587
Manufacturer #: 195422GS
This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/du...
$20.55
In Stock
Fuel Line Kit
PartSelect #: PS9269709
Manufacturer #: 199838GS
This is an authentic item that is supplied directly from the original equipment manufacturer for Briggs and Stratton Generators. This kit includes one (1) female quick connect, one (1) Male quick conn...
$95.77
In Stock
Gasket-exhaust
PartSelect #: PS9295033
Manufacturer #: 695398
This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cy...
$12.20
In Stock
Quick Connect, Fuel, 1/4 Barb
PartSelect #: PS9269225
Manufacturer #: 192695GS
This item is sold individually and is made of plastic. The fuel quick connect goes between the fuel line kit and the fuel valve. A set of pliers may be helpful when replacing this part. It will requir...
$55.07
In Stock
Common Symptoms of the 030253-0
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
... Read more
r />
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Read less
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!