0300 - Parts

Genuine Milwaukee replacement part, this item is sold individually. This Chuck Key tightens the jaws of the 1/2 inch capacity Chucks on all the Drill models shown below. For convenience a Chuck Key Holder part number 48-66-4040 can be ordered. It is attached to the power cord then the Chuck Key is attached to it.

This is a genuine Milwaukee replacement part, it is sold individually. The purpose of the 06-75-3150 Screw is to secure the chuck to the spindle of the models listed below. This is a left hand threaded screw, to remove it turn it clockwise. We do have an article and video on

This authentic replacement part is designed for use with Milwaukee drills/drivers. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Bearings experience constant wear from pressure, heat,...Read more vibration and friction. Because of this, many bearings need to be periodically replaced. This part is made out of metal and it is sold individually.

This is a genuine OEM sourced replacement part which is specially designed for use with Milwaukee power tools. It is a standard hardware which has multiple uses based on the model of your tool, please make sure to check the appropriate diagrams for the correct location and application of this component. This screw is made of high-quality ...Read moremetal and is sold individually, you will need a flat-head or a Torx screwdriver to secure or remove it.

Genuine Milwaukee replacement part This brush is sold individually, 2 are needed for the tools shown below It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore...Read more a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This bearing is an authentic part produced by the original manufacturer. It is compatible with a variety of Milwaukee handheld power tools. Ball bearings reduce friction between metal parts. They allow parts such as axles and shafts to rotate freely and steadily. Ball bearings are high wear components and are commonly replaced. Sold separately.

This cord protector is a genuine Milwaukee replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

It is an authentic manufacturer approved replacement item that is specially produced for Milwaukee drills. This metal bearing helps to secure intermediate pinion gear while allowing it to spin freely with minimal friction. Over time this part may wear out and restrict movement, if this happens it can easily be replaced. Please note this high quality item is sold individually.

This is an OEM part sourced directly from the manufacturer. The needle bearing is commonly found in Milwaukee power tools such as drills and screwdrivers. This part is made of metal, and is generally used to allow components in the machine to spin freely. It may be found in various locations in the machine, depending on model. Please ...Read morerefer to the parts diagram to be sure of ordering the correct part. You may require a screwdriver or wrench when replacing this part. This item is sold individually.

This is a genuine Milwaukee part, it is sold individually. The chuck is the top portion of the drill that holds the different drill bits. It is compatible with a variety of drills listed below. If your drill's bit retention is suffering, the rotation feels stiff, or the chuck has seized up entirely, a new chuck should fix the problem. Thi...Read mores chuck is made of metal. To install this chuck, thread the new chuck assembly onto the spindle. Secure the chuck assembly as tightly as possible( by hand). Open the chuck to accept the retaining screw. Install the retaining screw and secure the screw with a Phillips screwdriver. The screw is reverse-threaded ( requiring counterclockwise rotation to secure.

This is a genuine OEM sourced replacement power cord designed for Milwaukee electric drills/drivers. It deliers electricity the power tool. If the cord is damaged it is important to replace it immediately. Please note that the cord protector/sleeve is sold separately. Replacing power cord is an easy task and would only require a torx scr...Read moreewdriver. • Remove housing screws • Separate housing halves • Disconnect wires from the old power cord • Pull cord out through the protector sleeve • Remove old cord and secure new one in place • Reassemble in reverse order and test the tool