Microwave Sensors

Microwave Temperature Sensor

★★★★★

★★★★★

9 Reviews

The temperature sensor, also known as an oven probe, helps measure the temperature within the oven cavity. If your oven is too hot, not heating evenly, has little to no heat when baking, or flashing F3/F4 error messages on your control board, you may need to replace this part. This part measures 6" long and is made of metal. Please make sure to disconnect the power to your oven range before starting this repair. This temperature sensor is a genuine OEM part.

Microwave Temperature Sensor

★★★★★

★★★★★

22 Reviews

The oven temperature sensor for your range may also be called a probe. The quick connect on this part may differ than your original piece. If the temperature sensor does not fit you will have to cut off the quick connect, and then wire together with porcelain wire nuts. The function of the oven temperature sensor is to measure the temperature in the oven and signal the other heating components. Before you begin this repair make sure to disconnect the power to the range. The tools required for this installation include a number two Phillips screwdriver or a number two square head screwdriver, and maybe a pair of wire strippers and crimpers.

Microwave Range Oven Temperature Sensor

★★★★★

★★★★★

8 Reviews

This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will not start or has too little or too much heat, it is likely that the temperature sensor is bad, or defective. This temperature sensor features a 3.9-inch-long probe, 3.2-inch-long wire harness, and 1.7-inch-wide support bracket. Replacing this sensor is fairly simple but will require a screwdriver, wrench and drill with the appropriate Philips-head bit. Disconnect your range from the wall outlet and pull it out from the wall. Removing your range door is not necessary, but will make removing the sensor that much easier. You will now locate your temperature sensor, which will likely be near the heating element at the top/bottom of the oven. Remove any securing screws holding the heating element and/or sensor in place. At the rear of the range, disconnect and remove the rear panel to gain access to the electronics of the range. Disengage the sensor and its locking tabs, and may also require you to disconnect the terminals for the heating element if your temperature sensor is fastened to it. Remove the sensor and heating element (if necessary). If the sensor is connected to the heating element, use a wrench to unfasten it. Now you install the new temperature sensor and reassemble your oven, ensuring that wire terminals are connected correctly.

Microwave Oven Temperature Sensor

★★★★★

★★★★★

1 Review

The temperature sensor, also referred to as a thermostat, probe, or thermistor sensor, is responsible for measuring the temperature inside your oven. It is a platinum-resistance sensor with a resistance of 1000 ohms. If your oven is not heating evenly, not heating at all, or showing an error message, the sensor may be faulty. Typically located inside the oven, near the top, and attached to the rear wall, you can test the sensor with a multimeter. To do so, disconnect the power, remove the back panel, disconnect the wiring harness, and detach the sensor. Set the multimeter to ohms and touch the probes to the terminals. This test must be conducted at room temperature for accurate results. Refer to your user manual for guidance. If the test results show that the sensor is broken, you must replace it. This OEM replacement part is sold individually.

Microwave Range Sensor This sensor detects the temperature within the oven cavity.

Microwave Sensor This temperature sensor is an OEM replacement part designed for use in ovens/ranges. The sensor detects the temperature inside the oven and relays this information to the control board, which controls the heating elements in the oven. If the sensor experiences electrical failure or mechanical damage, you will likely notice uneven cooking, inaccurate temperature readings, and difficulties heating up the oven. You can access the sensor by either removing the back panel of your appliance or by reaching through the oven/range cavity from the front. Carefully disconnect the wires attached to the sensor and pull the sensor out of the appliance. Mount the new sensor in the correct position and reconnect the wires appropriately.

Microwave Range Temperature Probe

★★★★★

★★★★★

5 Reviews

Also known as a meat probe.

Microwave Sensor Experience a seamless cooking process with the Whirlpool Oven Temperature Sensor. An essential part for your range, oven or stove, it accurately measures the temperature inside the oven ensuring your meals are cooked to perfection. This genuine OEM part is compatible with various models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. Disconnecting the power before installing this part is highly recommended for safety reasons. Notably, despite the look-alike nature of many parts, minor size and shape variations could occur, hence, kindly verify the part number with your model before ordering. Finally, do consider wearing work gloves during installation to prevent any possible accidents.

Microwave Sensor This genuine temperature sensor ensures precise heat regulation inside your oven for consistent cooking results and improved safety. Designed to measure the oven cavity temperature, it communicates with the control board to adjust heating elements as needed, preventing overheating and maintaining even heat distribution. Ideal for resolving issues like inaccurate temperature readings or uneven baking, this sensor helps keep your appliance performing at its best. Installation is straightforward—simply disconnect the old sensor and secure the new one following your oven’s instructions.

Microwave Probe Introducing the genuine Frigidaire PROBE, MEAT TEMP, BLACK - a robustly designed tool crafted for several Frigidaire, Electrolux, White Westinghouse, and Tappan models. This meat probe ensures the precise measurement of internal temperature of meats during cooking, thus enabling you to attain accurate results every single time. The size and shape of this practical accessory are tailored to fit your appliance perfectly; however, do verify the part number for your specific model before securing your purchase. Follow your owner?s manual to get this part installed correctly. This meat probe is your essential cooking companion, catering to all your meat temperature measurement needs effectively. Discover the joy of exactness in culinary pursuits with the reliable and user-friendly Frigidaire meat probe.