Microwave Doors

Your Price

$35.17

Microwave Door Interlock Switch

★★★★★

(10)

PartSelect Number PS2361111

Manufacturer Part Number W10269458

This door interlock switch is for microwaves. Door interlock switch prevents the microwave from starting when the door is open. Because the microwave shielding and interlock switches must be properly tested following the door interlock switch replacement, a service technician should install this part.

Fixes these symptoms

Doesn’t shut off
Door not closing properly
No heat
See more...

Installation Instructions

Mark from HOMER GLEN, IL

Door switch inconsistent operation for Open/Close sensing.

Ordered top & bottom micro-switches and mounting plate parts. Internet reviews could not find specifics if the issue was due to a top/bottom or combination of micro-switch or mounting plate failure. Pulled the plug. Removed the top vent assembly cover held in by 2 Phillips screws inside the vent. Removed the control panel held in by 1 Phillip screw at the top vent assembly area. Lifted control panel upward to release the catch and moved it off to the side - didn't disconnect any leads. Used a Torx bit to remove the door switch mounting plates at the front and pulled the plates through the opening from the control panel. Documented the wire color code connections, the top plate uses 2 micro's with one using both the closed & open contact. Installed the respective micros on the mounting plates and worked backwards with the wiring and removal steps. Once completed, the open/close sensing has worked every time. Read more...

Your Price

$180.75

Door Assembly - Black

★★★★★

(3)

PartSelect Number PS11700861

Manufacturer Part Number WB56X24439

This door assembly includes the handle, panels, and shielding for your microwave. A faulty, or damaged microwave door can be dangerous, and should be replaced straight away. Before you start this repair, ensure the power and the high-voltage capacitor are disconnected from the microwave.

Fixes these symptoms

Door not closing properly
See more...

Your Price

$70.32

Door Frame - White

★★★★★

(10)

PartSelect Number PS1481562

Manufacturer Part Number WB55X10828

This is not the entire door just the outer frame.

Fixes these symptoms

Door not closing properly
See more...

Installation Instructions

Kelly from Austn, TX

The door panel and grille vent are plastic and thay both cracked and fell apart due to cheap plastic parts from GE.

Removed the screws at the top of vent and took the vent off and then removed the door by lifting it off the hinge. I had to break the old plastic door frame to get it off, but since it was no good anyway it didnt matter. Then I put the glass in the new frame put the handle on it and snapped the frame on to the door and put it back on the door hinge and then put the new vent on and screwed it down and closed the door. Job was not to hard at all. Read more...

Your Price

$22.99

PARTS ASSEMBLY

★★★★★

(4)

PartSelect Number PS7788764

Manufacturer Part Number AGM73812501

Installation Instructions

Gerard from FREDERICKSBRG, VA

broken door screw retainer

-remove vent by removing 2 screws holding it -remove door by lifting and moving aside -replaced broken door -used original glass in new door - reassembled in reverse order Read more...

Your Price

$181.78

Microwave Door Assembly

★★★★★

(1)

PartSelect Number PS12710041

Manufacturer Part Number WB56X32788

This door assembly is for microwaves. The door assembly includes the handle, panels, and shielding. A service technician should install the door assembly because the door contains shielding components. The technician must correctly test the microwave for leaks in the microwave shield before you can safely use the microwave.

Your Price

$261.53

Complete Door Assembly

★★★★★

(4)

PartSelect Number PS979712

Manufacturer Part Number 5304441374

This is the complete door, black in color.

Fixes these symptoms

Door not closing properly
See more...

Installation Instructions

Jarvis from Southern Pines, NC

The new door was not exactly like the old one

The old design was easier to install than the new one. I assume that the new part was changed to make it less expensive to manufacture. Installation of the new part was difficult but doable. Basically, the bottom of the door was located on the hinge tab and the top was then rotated into place until it snapped into place. Some force was required to get the door into place. A large screw driver was used to force the top hinge down so the door could be rotated onto the hinge tab. It would be possible to damage the door if too much force was used. Read more...