Ice Maker Sensors

Popular Ice Maker Sensors

Your Price
$54.25
  On Order
Ice Maker Bin Thermostat
★★★★★
★★★★★
(10)
PartSelect Number PS11740332
Manufacturer Part Number WP2313633
This is a bin thermostat made for standalone ice makers to activate the ice maker shut-off when bin is full. It senses how much ice is in the bin to determine if it should produce more ice or activate shut-off. The bin thermostat may need to be replaced if bin is overfilled, underfilled, or not producing ice. Thermistor can be tested with an ohm meter. This part is made of plastic and metal, and is white in color. This is an authentic part sourced from the original manufacturer.
Installation Instructions
Ray from Terry, MS
Ice maker overfilling with ice and would not stop production when full.
Very easy to replace. Down load the Manual online for a completely operating manual. Thermistor can be tested with an Ohm Meter. Proper values are listed in operating manual. Read more...
Your Price
$48.42
  In Stock
Ice Maker Bin Temperature Sensor
★★★★★
★★★★★
(5)
PartSelect Number PS11755842
Manufacturer Part Number WPW10511923
This bin temperature sensor is for ice makers. The bin temperature sensor monitors the temperature in the ice maker bin and sends the temperature reading to the electronic control board. Disconnect the power before installing this part. Wear work gloves to protect your hands.
Installation Instructions
Travis from N CHESTERFLD, VA
Ice bin overfilling
I'm an hvac/r technician, and regularly work on ice machines. Begin my pulling the white over beneath the control panel. It snaps in place so pull on the bottom then left out. 1/4 nut driver is all you need, and remove the screw holding the bin thermistor clip to the side. Up to the right , beneath the control panel, behind the plastic panel you previously removed is the mollex connector. Unplug the thermistor and follow instructions in reverse to reinstall. Read more...
Your Price
$60.26
  In Stock
Temperature Sensor
★★★★★
★★★★★
(3)
PartSelect Number PS11756166
Manufacturer Part Number WPW10548509
This is a temperature sensor. It may also be known as an ice maker sensor and is used in conjunction with your ice machine. This piece is roughly 3.5 inches long, almost 2.5 inches wide, and includes the necessary wiring connector. You will find this part located in the water pump area of the ice cube maker. The function of this part is to determine the water level within the water reservoir. Once the water level reaches a certain point, the sensor will signal the controls to fill the reservoir.
Installation Instructions
William from LANDRUM, SC
Ice maker would not make ice. I went through diagnostics and it showed the level sensor was not working. Water would continue filling the reservoir and not shut off to start making ice.
Took off several plastic covers to gain better accessibility to the sensor. Had to pull out the whole support piece to get at the part. Took out the old sensor, cleaned the unit as best as possible, then installed the replacement. Turned on the power to the unit and reinstalled all the parts I took out for better viewing and accessibility. Started up the unit and it is slowly building ice, which I will remove and dispose of to start getting clean ice. Read more...
Your Price
$42.13
  In Stock
Evaporator Thermistor
★★★★★
★★★★★
(1)
PartSelect Number PS11740333
Manufacturer Part Number WP2313635
Used with free-standing ice cube makers.
Your Price
$85.22
  In Stock
Sensor
PartSelect Number PS11755513
Manufacturer Part Number WPW10485962
Your Price
$53.84
  In Stock
Thermistor
PartSelect Number PS11755741
Manufacturer Part Number WPW10503764
This part monitors the temperature and sends the readings to the electronic control board.
Installation Instructions
Dennis from Houston, TX
IceMaker was overflowing so the suspicion was the Ice level sensor was working
The most difficult part of this order was identifying the part. The manual and picture for this model icemaker called the part a Ice level Sensor. No such item could be identified at Parts Select or at Kitchen Aid. After looking at item after item on the parts diagram it was determined the new name was a bin Thermostat not to be confused with the Thermistor, Ice control.
Replacement was quick and easy and took 5-10 minutes. Working fine now.
Read more...
Your Price
$41.41
  On Order
Thermistor
PartSelect Number PS11757112
Manufacturer Part Number WPW10683580
This part monitors the temperature and sends the readings to the electronic control board.
Your Price
$179.63
  In Stock
THERMISTOR BIN
PartSelect Number PS1017712
Manufacturer Part Number WR55X10545
Your Price
$37.42
  In Stock
Ice Control Thermistor
PartSelect Number PS11739075
Manufacturer Part Number WP2185680
Consisting of a thermistor inside a small case, is used to sense air temperature.
Installation Instructions
John from New Albany, IN
ice machine would not continue to produce longer than a couple of hours
buy unplugging thermisistor machine should stop making ice.buy loosening the top cover and front cover you can access the plug and thermisistor. Read more...
Your Price
$90.31
  On Order
THERMISTOR ICE CONTROL
PartSelect Number PS1019988
Manufacturer Part Number WR55X10544