General Electric Cooktop Igniters
Popular General Electric Cooktop Igniters
Your Price
$56.65
In Stock
General Electric Cooktop Flat Style Oven Igniter Kit
PartSelect Number PS231280
Manufacturer Part Number WB13K21
The flat style oven igniter kit comes with a mounting bracket and a wire connector with a plug. The igniter kit is used to light the oven burner. If you notice that your oven will not heat up properly, the igniter kit may need to be replaced. This flat style gas oven igniter has a body length of 3-3/4 inches. When completing this repair, the connector plug might need to be removed and spliced to the range wiring using porcelain wire nuts. Before you begin this repair, be sure to disconnect the power source from the oven, and shut off the gas supply.
Fixes these symptoms
- Element will not heat
- Gas igniter glows, but will not light
- Gas smell
- See more...
Installation Instructions
Sidney from Marysville, CA
The igniter glowed, but never got hot enough to ignite the propane, so I did smell propane.
First, I removed the two screws that held the heat shield in place. Second, I removed the one screw that held a small wire covering. That covering kept the wires inside the back wall of the range. Third, I removed the two screws that held the Igniter Kit, and unplugged it from the back of the range. I then carefully put the new igniter in, and reassembled everything in reverse order. It only took about 30 minutes to do the repair, and 30 minutes of cleaning and wiping of the broiler area. (It is amazing what you see when you take things apart). I should have been wiping things up over the past few months. Overall, a very easy repair. I ordered the part at 12:30 in the afternoon, and FedEx delivered it the next morning at 11:30, all for the regular shipping price of $6.95. VERY HAPPY.....
Read more...
General Electric Cooktop Surface Burner Spark Electrode
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way. Read more...
PartSelect Number PS231276
Manufacturer Part Number WB13K18
This part helps your burner ignite and produce flame.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Thomas from Bloomsbury, NJ
Burner igniter needed to be replaced
Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off. Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way. Read more...
General Electric Cooktop IGNITER GLOWBAR
PartSelect Number PS11725182
Manufacturer Part Number WB13X25261
Fixes these symptoms
- Gas igniter glows, but will not light
- Little to no heat when baking
- See more...
General Electric Cooktop ELECTRODE TOP
PartSelect Number PS1022004
Manufacturer Part Number WB13T10065
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
David from Cherryvale, KS
ignitor wouldn't spark
Compressing the spring to apply the retainer clip was some what of a challange. But, everything went fine. Mission accomplished.
Read more...
General Electric Cooktop Spark Igniter
I've replaced 2 igniters on this stove. My symptoms were that when I tried to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark. Read more...
PartSelect Number PS11736298
Manufacturer Part Number WB13X27058
Also known as spark electrode. This part helps your burner ignite and produce flame.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Jeffrey from Freehold, NJ
Burner wouldn't light
I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair. I've replaced 2 igniters on this stove. My symptoms were that when I tried to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark. Read more...
General Electric Cooktop Igniter
PartSelect Number PS224072
Manufacturer Part Number WB02X10822
Also known as spark electrode. This part helps your burner ignite and produce flame.
General Electric Cooktop Igniter Switch and Harness Assembly
PartSelect Number PS11721440
Manufacturer Part Number WB18T10454
The igniter switch and harness assembly includes the igniter switches and the complete wire harness for all the surface burners.
Related General Electric Cooktop Parts
- All General Electric Cooktop parts
- General Electric Cooktop Drip Bowls
- General Electric Cooktop Elements and Burners
- General Electric Cooktop Grates
- General Electric Cooktop Hardware
- General Electric Cooktop Knobs
- General Electric Cooktop Lights and Bulbs
- General Electric Cooktop Seals and Gaskets
- General Electric Cooktop Switches
- General Electric Cooktop Valves