My Orders
Generac Generator Carburetors
GET YOUR OFFICIAL Generac PARTS TO ENSURE VICTORY
Popular Generac Generator Carburetors
This is an OEM part sourced directly from the manufacturer. The carburetor is used in small engines from Generac. This is a complete carburetor assembly, and is used to mix air and fuel together for ignition within the engine. This item is sold individually.
This is an OEM part sourced directly from the manufacturer. The carburetor is used in small engines from Generac. This is a complete carburetor assembly, and is used to mix air and fuel together for ignition within the engine. This item is sold individually.
A carburetor controls how much fuel and air reach a portable generators engine. Varnish, corrosion, a sticking float, or a worn needle can make the engine hunt, run unevenly, stop under load, or refuse to start. A complete replacement assembly may be useful when cleaning and basic service do not correct the fault. Compare the mounting pattern, throttle and choke linkages, fuel connection, and full engine code before ordering. New mounting gaskets may need to be purchased separately. Shut off the fuel, disconnect the battery and spark plug, and label every connection. After installation, check for leaks and confirm stable speed and output under the recommended test load.
A carburetor controls how much fuel and air reach a portable generators engine. Varnish, corrosion, a sticking float, or a worn needle can make the engine hunt, run unevenly, stop under load, or refuse to start. A complete replacement assembly may be useful when cleaning and basic service do not correct the fault. Compare the mounting pattern, throttle and choke linkages, fuel connection, and full engine code before ordering. New mounting gaskets may need to be purchased separately. Shut off the fuel, disconnect the battery and spark plug, and label every connection. After installation, check for leaks and confirm stable speed and output under the recommended test load.
Installation Instructions
Robert from BATON ROUGE, LA
Carberator gummed up from sitting in storage. Fuel gone bad in the tank
With a 12-in-one nut screwdriver I removed the two bolts holding the breather cover and air filter. Then I used about a 9/16 deep socket ratchet to remove the nuts holding the breather housing to the carburetor assembly studs. A pair of needle nose pliers was used to disconnect the throttle then I wriggled the breather cover away from t
... Read more
he carburetor so I could get to the fuel line. I managed to pull the fuel line off the carburetor and from the shut-off valve at the tank. The carburetor slid freely and easily off the carburetor studs and I was careful not to damage the carburetor gasket since none came with the new carburetor. I used a single edge razor blade to free the gasket from the old carburetor. A very small amount of silicone lube was used on the gasket and then I sandwiched the old gasket between the carburetor intake and the new carburetor and attached the throttle connection. Before beginning the reassembly I unscrewed the shut-off valve from the tank and used a funnel to drain the very old fuel into a 5-gallon bucket. I made sure the valve was clean by spraying carburetor cleaner through it and did the same with the old fuel line, making sure everything was clear of any obstruction. Then replace the breather assembly back over the carburetor studs, snugged the nuts back on and then replaced the air filter and cover. I re-attached the fuel line to the fuel valve and the carburetor, added a half gallon of clean fresh fuel and was ready for a smoke check. Pulled the starter rope three times with the choke full on, then turned to half-choke and the puppy started right off. I then turned the choke completely off and the engined purred along. I then exercised the generator by plugging in and running a number of power tools for about 15 minutes. Followed standard shut off procedures and the generator is ready for use. Saving the old carburetor to be cleaned and held on reserve for the future. Might want to have another gasket handy or some gasket material should it have to be replaced in the future.
Read less
Carburetor
Carburetor
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This is an authentic Generac part that has been sourced from the original manufacturer to be used with portable generators. The carburetor connects to the cylinder and is used to supply the engine with a mixture of fuel and air. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement. To ensure the proper repair procedure, refer to the appropriate diagrams for your model. A wrench set will be needed to replace this carburetor assembly. Keep in mind this high-quality assembly is sold as an individual item.
This is an authentic Generac part that has been sourced from the original manufacturer to be used with portable generators. The carburetor connects to the cylinder and is used to supply the engine with a mixture of fuel and air. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement. To ensure the proper repair procedure, refer to the appropriate diagrams for your model. A wrench set will be needed to replace this carburetor assembly. Keep in mind this high-quality assembly is sold as an individual item.
Carburetor
Carburetor
