Edger Bearings

Edger Flange Bushing This authentic manufacturer-supplied part is designed for Craftsman snowblowers. Flange bushings are used to provide support for components while allowing them to rotate with minimum friction. It is made of high-quality material and is sold individually. Make sure to check the diagrams for your model to ensure the correct replacement procedure. You may need a screwdriver and a wrench set to take apart and reassemble the equipment when performing this repair.

Edger Ball Bearing 6201 This single-row, deep-groove ball bearing is sized at 12x32x10mm and is made of durable metal. It is used to reduce friction and vibrations when it is in between two parts that are rotating or moving against each other. This bearing can handle forces that are applied to it up-and-down and sideways, also known as radial and axial loads. It is easy to install and can handle high rotational speeds without causing too much vibration or making much noise. Over time, this ball bearing wears out from heat and pressure and starts to fail. If the engine of your machine has been run without oil in the gas tank, this ball bearing can seize. In these situations, you will need to replace the ball bearings. Otherwise, you will notice that your machine overheats, works harder because of the increased friction it is handling, and produces excessive vibration and noise. To extract a ball bearing from your machine, you will need to insert a flat-head screwdriver through the bearing opening and against the seal. Then, tap the seal out with a mallet. Afterwards, slot a socket through the diameter of the bearing, and tap the entire bearing out of its place by again using a mallet. This authentic OEM part is sold individually, so be sure to refer to your user manual to verify how many bearings your machine needs and where they are in it.

Edger Ball Bearing (6203zz) This is a genuine replacement part sourced from the original manufacturer for use with edgers, sanders, and miter saws. The special ball bearing is commonly used to reduce friction between a rotating shaft and fixed part assembly. This ball bearing is available as an individual replacement please see model diagram for associative parts.

Edger Lawn Mower Bearing This sealed ball bearing is used in mower deck spindle and pulley assemblies to reduce friction and support smooth rotation. Designed to fit securely in the housing, it helps extend component life and maintain consistent cutting performance. It’s a direct replacement for worn or noisy bearings during deck or pulley service.

Edger Bushing This is an authentic manufacturer sourced replacement part designed for use with Toro walk-behind lawn mowers. This part helps to secure the mower wheel, allowing it to rotate freely. It is made out of metal and it is sold individually. To replace this part you would need a wrench and pliers.

Edger Brg-ball .500x1.38x.437 This authentic OEM sourced replacement part is specially designed for use with Ariens lawn and garden equipment. The ball bearings are used to reduce friction between rotating parts, the rollers help to distribute the weight evenly while the minimal contact area reduces friction. Over time components may wear out and begin to crack eventually requiring a replacement, please note this high-quality metal bearing is sold individually.

Edger Bushing Axle This is a genuine Snapper part. The axle bushing is constructed of high-quality metal, and is compatible with many lawn mower devices. This part helps to reinforce the front and rear wheel rims. Keep in mind this item is sold individually. A wrench and a screwdriver are needed in the removal and replacement.

Edger Bearing-flange The Hex Flange bearing, .630 inches I.D. is an OEM part. Black in color and made of metal, it is sold individually. It is installed using a wrench or socket and its installation has been rated as Easy by consumers. This part attaches on the worm gear shaft in the cute, and is used to secure the worm gear on the shaft. If broken, you will no longer to be able to control the chute (or you may only have partial control). This breakage can occur due to fatigue over time, and means the part must be replaced. Refer to your owners manual or model number to ensure you are purchasing the correct part.

Edger Bearing, Ball - 6001 This authentic replacement ball bearing is supplied by the original equipment manufacturer for use with Shindaiwa and Echo handheld tools. Ball bearings are used to reduce friction between rotating parts, over time due to heat, pressure and vibration the components may wear out and begin to fail eventually requiring a replacement. For correct location and use of the part, make sure to check appropriate diagrams of your model. This high-quality bearing allows is made of durable metal and it is sold individually.

Edger Trimmer Bearing This silver metal Ball Bearing is manufacturer certified, and used to reduce the friction between parts, and comes individually sold. If broken or worn down, you will hear a grinding, growling, stretching, or rumbling sound, and the part should be replaced. Installing this new part requires a bearing puller. Refer to your make, model and diagram to check if this is the right part.