Cooktop Hardware

Your Price

$6.40

Cooktop Range Torx Screw

PartSelect Number PS11741257

Manufacturer Part Number WP3368921

7-18 x 3/4-Inch - sold individually.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Michael from Dardanelle, AR

Ignitor switches shorted out

The ignitor switches are installed on top of the 4 gas valves for the range top. These switches control the electronic ignition. To replace the switch assembly the top of the range must be removed to gain access.

This was made more difficult by the fact that the screws that hold the burners to the range top were rusted and had to be drilled out so the the burners could be released from the top.

1. Disconnect the power to the range.
2. Open the top oven door.
3. Remove 2 - 1/4" sheet metal screws at the front corners of the range top assy. Remove the Burner knobs and the two Phillps screws that holds the gas valve assembly to the range top.
4. With a drill, remove the tops of the screws to release the burners from the range top. If the screws are in good condition and just unscrew them and the upper burners from the Orifice Holders. (I had to replace the orifice holders because the screws were stuck in them due to rust).
5. When the burners are free, lift the range top at the front and remove it from the range. Disconnect the ignitor wires from the ignitors on each holder.
6. To replace the Orifice Holders, disconnect the gas supply pipes from each holder by loosening the compression nut at the holder using an adjustable wrench. Secure the Orifice Holders when loosening the fittings, BE CAREFUL not to damage the aluminum gas supply pipes.
7. Note that there are 3 different Holders, be sure to use the holder that matches the specific location.
8. For LP gas fueled ranges ONLY, remove the small gas jets from the old holders and install them in place of the parts supplied with the new orifice holders. The new parts contain NATURAL GAS jets which are not compatible with LP gas. Each Different Orifice Holder uses a specific orifice or jet, make certain that the orifice matches the orifice holder. Check for leaks at the gas connections using soapy water.
9. Carefully raise the old ignitor switches (4) off the shafts of the gas valves. Note the top and bottom configuration of the switches
10. Carefully release the wires that come from the rear of the range from the rearmost switch. Press a suitable pin or other suitable tool in a the hole, beside the wire, just enough to release the wire. (Look at the NEW switch assemble to see how this works). Remove the wires from the NEW switch first to see how it is done. Repeat the process on the old switches. (you will re-use the wires that come up from the rear of the range.
11. Install the new switch assembly over the four (4) burner gas valves, take care to align the "D" shaped shafts with the holes in each valve.
12. Insert the wires in the two connections on the rearmost switch. CAUTION!!! Be sure to install the wires so that the color codes agree with the wires on the new switch assembly. Black to black and gray to gray.
13. Install the 4 clear plastic "shields" over the shafts and against the top of each switch.
14. Re-connect the ignitor wires to the burners and Re-Install the range top, in the reverse order of dis-assembly. Read more...

Your Price

$16.09

Cooktop Bumper - Black

★★★★★

11 Reviews

PartSelect Number PS4704188

Manufacturer Part Number WB28T10278

This authentic GE replacement bumper is sourced directly from the original manufacturer and is designed for use with gas cooktops. It provides a cushioned barrier between the cooktop’s main surface and the grates, helping to reduce noise and prevent damage from contact. Ideal for maintaining the stability and longevity of your appliance, this bumper is sold individually—please note that up to four may be required for a complete replacement.

Installation Instructions

jack from SEYMOUR, WI

On/ off knob for gas cooktop was cracked

Ordered new knob and fit on perfectly Read more...

Your Price

$7.47

Cooktop Range Igniter Screw

★★★★★

3 Reviews

PartSelect Number PS11745563

Manufacturer Part Number WP8273062

This screw is sold individually.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Didier from LONE TREE, CO

Ignitor did not work

- Removed the cover.
- Removed te two Torx screws.
- Pulled the burner a couple of inches to be able to disconnect the wire.
- Spent a lot of time removing the small Philips screw holding the ignitor. Ended up breaking the ignitor with pliers to be able to put WD40 under the screw's head.
- Treated all screws with a high temperature copper paste to prevent oxidation.
Installed the new ignitor with the new screw.
- Reconnected the wire.
- Installed the two Torx screws.
- Voila, it works. Read more...

Your Price

$21.45

Cooktop Washer Screw

★★★★★

2 Reviews

PartSelect Number PS12741703

Manufacturer Part Number W11404293

Sold individually.

Fixes these symptoms

Lid or door won’t close
See more...

Installation Instructions

Ed from NEW BERN, NC

Replace hinge and hinge spring assembly.

I mounted the left and right hinge assemblys into the washer (spring assembly) and then mounted the glass top on to the hinge assemblies. Inserted the screws and tightened as required. Read more...

Your Price

$16.45

Cooktop Receptacle Push-in

★★★★★

9 Reviews

PartSelect Number PS752188

Manufacturer Part Number WB08T10026

This part is the replacement light socket for your oven. The oven light socket provides power to the light, and at the same time holds the light bulb in place.

Installation Instructions

Richard from Menifee, CA

No problems encountered.

Used nutdriver to remove screws holding cover over oven light socket, unclipped electrical connectors, removed socket by hand, then reversed the foregoing. Easy. Read more...

Your Price

$7.47

Cooktop Dryer Screw

★★★★★

2 Reviews

PartSelect Number PS11746840

Manufacturer Part Number WP90767

This screw is sold individually.

Installation Instructions

Alexander from Lakeland, FL

Broken Dryer Knob

First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...