Chainsaw Starters

This is an OEM replacement recoil kit supplied directly by Poulan. The starter pulley spins the flywheel to start the engine when you pull the starter rope. The most common reason for replacing the starter pulley is if the starter rope won't retract. Please note this kit does NOT include the rope and rewind spring. When replacing this part make sure to disconnect the spark plug wire before starting repair.

Also referred to as a Recoil Spring, this OEM replacement part is used to rewind the pull rope back into the starter housing. This Spring is sold individually, not as part of a kit or assembly, and is made of metal. If the pull cord will not retract into the housing, inspect the Recoil Spring for signs of wear or damage, replacing if necessary. You will need a screwdriver to complete this repair. Customers rate this repair as Easy.

This is an authentic OEM part for use with Craftsman Chainsaws. The recoil starter repair kit replaces the parts of the engine\\\'s recoil starter susceptible to normal wear. The most common reason for replacing the recoil starter repair kit is if the engine won't turn over when starter rope is pulled the Starter rope pulls too easily (and without resistance) the Starter hub is not engaging the flywheel or the Starter hub is not turning with the pulley (when the rope is pulled). This part includes starter pulley the assist spring and the starter hub. Here is a list of tools that are needed to install the recoil starter repair kit Phillip's screwdriver, Torx drivers, long-nosed pliers, and scissors or wire cutters (optional).

The chainsaw starter rope is a three-foot-long white rope that is approved by the original equipment manufacturer, and which wraps around the recoil pulley and is pulled to start the engine. Installation is rated as "Easy" by customers and requires a screw driver, pliers, and torx screwdriver. If the rope breaks it should be replaced. Refer to your make, model and diagram to ensure this rope is right for your machine.

This authentic manufacturer-sourced replacement part is specially produced for use with Kohler engines commonly installed on Toro lawn and garden equipment. The starter motor provides an initial motion, engage the flywheel to start the engine. Please note this high-quality component is sold individually.

This is an authentic OEM sourced replacement part designed for use with Husqvarna chainsaws. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually. To complete this repair you would need a screwdriver.

This part is an OEM from Husqvarna for use with Husqvarna Chainsaws. The recoil starter assembly spins the crankshaft to start the engine when you pull the rope. This part is sold individually. The most common reason for replacing the recoil starter assembly is if any of the parts it contains the starter rope, the rewind spring, and the recoil starter pulley is worn out or broken, causing the engine to not start. These parts can also be purchased and replaced individually. The toll that you will need to install the recoil starter is a screwdriver.

This stator kit (15 amp) is an OEM part direct from Kohler. Composed of metal, wiring and protective plastic, the kit is made for use with many small engines. This component provides the necessary voltage for charging the motor battery. A wrench and a pair of pliers are helpful for making the installation. Please refer to the manual for additional repair instructions.

This is an original part from Craftsman for edgers and chainsaws. This part helps turn the flying wheel when you pull on the starter rope. You may need a wrench set to replace this part. It is recommended to review your models diagram to verify the parts compatibility. This part is made of durable plastic and sold individually.

This replacement part is sourced from the original equipment manufacturer. It is specially designed for use with Poulan, Husqvarna and Jonsered chainsaws. The spring is an important component of the starter mechanism. It applies tension on the pulley allowing it to retract. Unfortunately, over time it may wear out, get damaged or lost eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. This high-quality spring is made of durable metal and is sold individually. You will need a screwdriver to take apart the starter housing in order to perform this repair.