Official Caloric Air Conditioner Parts | Order Today, Ships Today

Heating Element Brass Nut – Part Number: 154106202

Your Price

$11.15

Heating Element Brass Nut

★★★★★

(8)

PartSelect Number PS1524878

Manufacturer Part Number 154106202

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step guide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.

Fixes these symptoms

Leaking
Not cleaning dishes properly
Not drying dishes properly
See more...

Installation Instructions

Dennis from Tryon, NC

Water leaking under the dishwasher

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed. Read more...

Faucet Adapter – Part Number: WPW10254672

Your Price

$49.39

Faucet Adapter

★★★★★

(21)

PartSelect Number PS11751238

Manufacturer Part Number WPW10254672

The faucet adapter for your portable dishwasher or washing machine attaches to the faucet and allows you to connect the machine to the tap. Before you install the faucet adapter on your taps, be sure that it fits the coupler on your dishwasher or washer. As per the factory, this is used for faucets with inside or outside threads. For female connection (outside) just remove the washers. This adapter is approximately 1 inch in length, and slightly less than one inch in diameter. This adapter comes with two different thicknesses of rubber washer. You will not need to use both so be sure to determine which thickness works best for your tap before installing it.

Fixes these symptoms

Leaking
Will not fill with water
See more...

Installation Instructions

Stephen from Enfield, CT

faucet attachment would not sit correctly in hose connector to portable dishwasher. Received machine second hand. Could not find a replacement faucet adapter. So ordered new one and hose plus connector.

Turned machine on side. Removed two casters with Wonder Tool prybar. Then used it to remove plastic push screws holding cardboard bottom cover. Unscrewed water hose. Used screwdriver to remove clamp on drain hose. Stood machine upright, opened door. Unscrewed two screwsfrom tabs into woodblock top. Slid top forward and removed it. Cut plastic hose retainer. Removed hose assembly. Installed new hose by reversing steps. Used a new wire strap to hold hoses in place on top corner of machine. Read more...

Your Price

$10.72

Hose Clamp

★★★★★

(2)

PartSelect Number PS11740613

Manufacturer Part Number WP285655

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Stephen from Laveen, AZ

Drive Pump Leaked

It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on. Read more...

Your Price

$7.76

Zip Tie

PartSelect Number PS11753208

Manufacturer Part Number WPW10339879

Your Price

$11.92

Coupler Gasket

PartSelect Number PS11746842

Manufacturer Part Number WP910218

Fixes these symptoms

Leaking
See more...

Faucet Adapter Coupling – Part Number: 5304490369

Your Price

$45.68

Faucet Adapter Coupling

★★★★★

(4)

PartSelect Number PS7321390

Manufacturer Part Number 5304490369

This part connects the drain hose to the sink.

Installation Instructions

Liza from Hazel Park, MI

Purchased used appliance that needed parts

I purchased a wonderful portable dishwasher at a garage sale for $20. The woman had just redecorated her kitchen and was selling the relatively new portable model. All it needed was a new caster and a faucet adapter. After ordering the parts, they arrived in a couple days, and after less than 5 minutes of installing them I had a "new" dishwasher that works like a champ! Thanks for making this so easy! Read more...