Caloric Air Conditioner Hardware

Caloric Appliance Parts
Shop By Part Type

Popular Caloric Air Conditioner Hardware

Your Price
$6.72
  In Stock
Heating Element Brass Nut
★★★★★
★★★★★
(8)
PartSelect Number PS1524878
Manufacturer Part Number 154106202
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step guide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.
Installation Instructions
Dennis from Tryon, NC
Water leaking under the dishwasher
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed. Read more...
Your Price
$5.52
  In Stock
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...
Your Price
$5.52
  In Stock
Screw
★★★★★
★★★★★
(2)
PartSelect Number PS11747542
Manufacturer Part Number WP98165
This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.
Installation Instructions
Lynn H from MILL CREEK, WA
Hinge pin for drawer lid broke
1. Remove all drawers {3}, shelves {glass 1}, shelf support {1}. 2. Remove two {2} screws from End Cap. 3. Carefully remove End Cap and drawer temperature control part on the back wall keeping them aligned as installed. The part on the back wall swings out so that the tab on the left end of the piece may be withdrawn from the securing slot (hole). The two parts should be carefully removed while keeping the two parts at a right angle the way they are installed. The reason for this caution follows. 4. On the back side of both parts are plastic pieces that, I believe, can be easily broken if you are not aware. The pieces are connected together at the right angle. They are the control arms for the temperature control -- on right side End Cap only -- the left side doesn't have them or the rear part on the back wall. 5. The pieces must be disconnected and removed. You must examine and ponder how they are held in place and hooked together in order to disconnect and remove them without damaging them. The same advice is applicable to reinstalling the pieces in the new part -- End Cap. 6. After reassembled and keeping the two parts at a right angle, insert the tab on the left end of the back wall part into the slot (hole) and swing the two parts back into position. 7. Replace the screws. 8. Done, reinstall the shelf, shelf support, and the drawers. NOTE: I ordered the two screws but they were not needed. Read more...
Your Price
$3.38
  In Stock
Element Grommet
PartSelect Number PS451462
Manufacturer Part Number 5300806833
This grommet is used in a number of household appliances. Most often it is used in the dishwasher as part of the assembly that mounts and holds the heating element in place. This replacement part is made out of rubber, which helps create a seal between the element and the appliance. This grommet is sold individually. If you are replacing the heating element, or the brass nut that holds it in place, we recommend you replace the grommet at the same time. Before you begin any repair work on your dishwasher, make sure you have unplugged it and shut off the water supply.
Fixes these symptoms
Installation Instructions
Eric from Holly, MI
Water leaking from under dishwasher
Removed lower trim covers (2 Phillips screws) disconnected power supply at breaker box. Removed wire from heating element, removed (broken) brass nut, unclipped heating element and removed. Removed flat washers and replaced with new grommets. Kind of tricky getting them in there. Also had to lube them with silicone to get the element back through. Installed new brass nuts and installed wire connectors. Reset breaker and started diswasher to verify repair. No leaks, working just fine, reinstalled lower trim covers Read more...
Your Price
$10.76
  In Stock
Hose Clamp
★★★★★
★★★★★
(2)
PartSelect Number PS11740613
Manufacturer Part Number WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Fixes these symptoms
Installation Instructions
Stephen from Laveen, AZ
Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on. Read more...
Your Price
$5.52
  In Stock
Screw
PartSelect Number PS11742742
Manufacturer Part Number WP489349
This screw is sold individually.
Your Price
$5.52
  In Stock
Single Hex Head Screw
PartSelect Number PS11742731
Manufacturer Part Number WP489069
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
Installation Instructions
Chris from Pompano Beach, FL
Water in bottom of dishwasher
Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked! Read more...
Your Price
$5.52
  In Stock
Screw
PartSelect Number PS1845599
Manufacturer Part Number 67006425
This screw is sold individually
Your Price
$5.52
  In Stock
Screw - 8-18 x 1/2
PartSelect Number PS11742751
Manufacturer Part Number WP489464
Sold individually.
Your Price
$5.52
  In Stock
Screw
PartSelect Number PS11738661
Manufacturer Part Number WP12990527

Related Parts