Ariens Snow Blower Hardware

Ariens Snow Blower Shear Bolt Service Assembly This shear bolt and nut, also known as the shear bolt assembly, is sourced from the original manufacturer, and it is guaranteed to fit your snowblower. Each assembly includes one metal shear bolt and one metal nut, located at the connection point between the auger and gearbox/shaft. It is a safety mechanism designed to protect the snowblower auger from damage caused by sudden stops or excessive resistance. When the auger encounters a blockage or excessive load the shear bolt will break thereby preventing more severe damage to the gearbox. Once the bolt is sheared, it will need to be replaced. The bolt will also need to be replaced if it is bent or worn down, as a faulty shear bolt can result in damage to the auger, gearbox, and motor, as well as reduced equipment ability to throw snow, and increased safety risks. Use a socket or wrench to unthread the nut and remove the broken shear bolt. Align the new shear bolt with the mounting hole and secure it with the new nut. Note that this is a common repair and it is best to have several spare shear bolts and nuts on hand.

Ariens Snow Blower Shear Bolt Service Assembly This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, inspect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

Ariens Snow Blower Nut-lk-top-flg .312-18 Gf Zcc This is a genuine OEM sourced replacement part designed for use with Ariens snow blowers/throwers. It is a standard hardware which has multiple applications based on your unit. Please refer to diagrams for proper application. It is made out of metal and it is sold individually. You would need a wrench to tighten/loosen this nut.

Ariens Snow Blower Bolt- Modified Head Carriage This is a carriage bolt designed for Ariens snow blowers/throwers and it is sold individually. It is an authentic OEM sourced replacement part generally used to attach scraper blade. The square area under the head is designed to fit into a square hole in the workpiece. It is this square hole that restrains the bolt and keeps it from turning when the nut is tightened. Please note the lock nut is sold separately. When replacing this bolt you would need a wrench to remove or secure the nut.

Ariens Snow Blower Lawn Mower Screw This manufacturer-sourced replacement screw is designed for use with Ariens snow blowers and throwers. As a standard hardware component, it has multiple potential applications depending on the model. Made of durable metal, this part is sold individually. A wrench is required to tighten or loosen the screw during installation or removal. For proper use and placement, please refer to your equipment’s diagrams.

Ariens Snow Blower Pin-roll .250x1.75 This roll pin is a genuine OEM part that is designed for use with various makes and models of snowblowers and lawn tractor snowblower attachments. Made of metal and sold as an individual part, this pin features a 0.25-inch diameter and 1.75-inch length. This pin is hollow and features a split lengthwise down the middle to allow it to fit within tighter spaces and reduce the movement between two parts, such as the shaft or axle. If your snowblower is not performing well or has seen a decrease in power, check to make sure the roll pin is not damaged. To remove and install a new roll pin, you will need a hammer and a punch, and will simply need to punch out the old pin and punch in the new one.

Ariens Snow Blower Bolt This is a genuine manufacturer-approved carriage bolt, designed as a standard replacement part that fits a variety of products. It features a square section beneath the head, which fits into a matching square hole in the workpiece. This design prevents the bolt from turning while the nut is being tightened, ensuring a secure and stable fit. Please note that this item is sold individually and does not include the nut.

Ariens Snow Blower Pin- Spring Clip

★★★★★

★★★★★

1 Review

It is a genuine OEM sourced replacement part, it is specially designed for use with Ariens snowblowers. This spring clip pin has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this hardware. Note this durable metal item is sold individually.

Ariens Snow Blower Nut-rtnr .25-20x.56 This is an authentic Ariens replacement part manufactured for use with snowthrowers. The retainer nut is used to secure various part assembly which depends on the model of snowthrower. This retainer nut us sold as an individual replacement part, please see model diagram for part location and usage.

Ariens Snow Blower Bolt, 5/16-18x2 This bolt is a genuine OEM replacement part used in a variety of lawn and garden equipment. It is 2 inches long with a head diameter of 5/16 inches, and a thread pitch of 16 threads per inch. The bolt is used to secure the upper and lower handles on your equipment. If the bolt is stripped or damaged, your handles will become loose and fall out of alignment. You may also notice increased shaking when using your equipment. Replace the bolt promptly as the handles can eventually collapse. Each bolt sold individually.