My Orders
Admiral Ice Maker Hardware
GET YOUR OFFICIAL Admiral PARTS TO ENSURE VICTORY
Shop By Part Type
View MorePopular Admiral Ice Maker Hardware
Sold individually.
Sold individually.
Sold individually.
Sold individually.
Installation Instructions
Gayle from COUPEVILLE, WA
Replacing burning assemblies and rusted screws
Installing the 2 new burner assemblies worked great with the new screws. New screws however, did not work with the old burner assemblies that have rusted screws I wanted to replace. New burner assemblies are slightly taller that the old ones.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
Installation Instructions
Ronald from Northfield Center, OH
changing stove and dishwasher to match new frig.
I actually replaced parts on my black double stove to make it into stainless. We purchased a new frig and needed to replace parts on our stove and dishwasher so they would match. They look beautiful, all the parts shipped when they were suppose too. Ordering from this company was top notch. Would order again if needed.
This is a speed lamp clip, and may also be known as the water line spring clamp. It is used in conjunction with your refrigerator. If you have a leak at your fill tub, this part may be the reason. The function of this clip is to keep the fill tube and the water line connected. This will allow water to flow freely without leakage into your water/ice dispensers. This part is quite small, with less than a half-inch in outer diameter. The clip is an off-black, almost olive color, and is rounded.
This is a speed lamp clip, and may also be known as the water line spring clamp. It is used in conjunction with your refrigerator. If you have a leak at your fill tub, this part may be the reason. The function of this clip is to keep the fill tube and the water line connected. This will allow water to flow freely without leakage into your water/ice dispensers. This part is quite small, with less than a half-inch in outer diameter. The clip is an off-black, almost olive color, and is rounded.
Installation Instructions
Richard from Yarmouth, ME
Leak at fill tube
Removed two screws that held cover plate. remove cover plate. Remove water hose, and clamp, by compressing clamp with pliers. Remove fill tube by pulling HARD, from back.
Replace fill tube, check to be sure that it entered ice maker properly. Replace hose and clamp.
Replace cover and screws.
Replace fill tube, check to be sure that it entered ice maker properly. Replace hose and clamp.
Replace cover and screws.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This screw is sold individually.
This screw is sold individually.
Installation Instructions
Joseph from Baldwin, NY
dryer did not shut off no heat
took control pannel apart removed timer took new timer and replaced wire for wire the mounted new timer . removed old buzzer and replced wire for wire then mounted new buzzer screw was just in case I lost or stripped old one not needed . reassembled control pannel ,tested and found I needed more parts no heat so I opened the bottom and I
... Read more
ordered Igniter, sensor ,and thermostat and new coil kit . now i have heat but thermostat is back ordered timer works but not on regular auto dry but I do have heat ?? it has to be thermostat . now all the repair was relitivly easy but you had to watch and be carefull of what you were doing . when thermostat comes in I hope that will solve all the problems if not
Read less
Sold individually.
Sold individually.
This screw is sold individually.
This screw is sold individually.
This water tubing clamp keeps the 3/16-inch diameter water tubing mounted to your refrigerator. Its purpose is to prevent shifting, kinking, or loosening of the tubing, ensuring a consistent water flow for the water dispenser and ice maker. It is typically located at the back of the cabinet near the inlet valve. If the clamp securing the tubing in your refrigerator is not properly secured, it can result in leaks or complete detachment. This poses a risk of water damage to your fridge, flooring, and nearby structures if not addressed promptly. To replace the clamp, refer to your user guide for its location. Then, use a screwdriver to remove the securing screw. Please note that this clamp is sourced directly from the original equipment manufacturer and does not include any additional hardware.
This water tubing clamp keeps the 3/16-inch diameter water tubing mounted to your refrigerator. Its purpose is to prevent shifting, kinking, or loosening of the tubing, ensuring a consistent water flow for the water dispenser and ice maker. It is typically located at the back of the cabinet near the inlet valve. If the clamp securing the tubing in your refrigerator is not properly secured, it can result in leaks or complete detachment. This poses a risk of water damage to your fridge, flooring, and nearby structures if not addressed promptly. To replace the clamp, refer to your user guide for its location. Then, use a screwdriver to remove the securing screw. Please note that this clamp is sourced directly from the original equipment manufacturer and does not include any additional hardware.