Uni Washer Hardware

Your Price

$11.75

Uni Washer SCREW

PartSelect Number PS417085

Manufacturer Part Number 131168200

Sold individually.

Installation Instructions

Glenn from Fort Worth, TX

Dryer squealed loudly

First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst. Read more...

Your Price

$11.21

Uni Washer Screw

PartSelect Number PS417463

Manufacturer Part Number 131302800

This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Installation Instructions

Edward from Baltimore, MD

Drying too slowly

Removed access plate from back bottom left
Removed belt from motor
Needed to lift up top of dryer
Inserted flathead screwdirver in front under top to push in two metal clips holding top down
Lifted up top of dryer
Removed 2 screws holding on front of dryer
Removed front of dryer
Broke Door Switch removing front of dryer. I should have depressed the metal sides in and pulled switch through hole.
Instead, I tried to remove the leads. This broke the fragile prongs.
Started dryer (with belt removed so drum doesn't spin)
Verified ignightor came on every heating cycle
Gas turned on properly
Gas turned off after 90 seconds
Gas never came back on
Indicitive of bad coils
New coils solved the problem
Replaced door switch and lint trap cover in the process. Read more...

Videos!

Your Price

$25.94

Uni Washer Screw-In Plastic Leveling Leg

★★★★★

4 Reviews

PartSelect Number PS1152204

Manufacturer Part Number 134548800

This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your appliance to make it leveled. This model is made entirely of plastic and is white in color. It is just under 2.5 inches long, 1.5 inches wide, and the head has a diameter of roughly 1.5 inches.

Installation Instructions

Sandra from Denton, TX

Stopped agitating versus level washer feet/leg

My washing machine stopped agitating and spinning and I couldn't afford a repair man...plus I wanted to exhaust any obvious problems first. One of the leveler feet had broken years ago. Since I luckily had determined via reading other posts that the agitator won't work if the cycle safety switch is not functioning right, I thought the safety switch might need to be changed but after careful thought, I decided to order a new levelling leg first because maybe the broken levelling leg was shaking the safety switch so it wasn't connecting right. Once I received the leg overnight, I flipped the washer on its side and had to drill out the old leg. It was a little tricky because of how it broke, but the drill worked. I flipped the washer back up, leveled it with the new foot, and the agitator was miraculously working again...just like new. I didn't need the safety switch. Thanks to partselect.com for having the details of my washer parts to study up on and get me the right part so quickly. I saved myself alot of money. Read more...

Your Price

$16.13

Uni Washer CLAMP

PartSelect Number PS5574235

Manufacturer Part Number 5304488479

Clamp used for hoses.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Jeffrey from Gulf Breeze, FL

dryer squeeked and rattled

after removing the panel covering the dryer blower and removing the blower cover, i pulled the old blower wheel off and placed the new whell on carefully lining the flat edge of the wheel hole up with the flat edge on the blower piston, the n i placed the clamp on and put back all the housing covers and panels...and now my dryer runs quiet and drys cloths fast....thanks to partselect!!!! Read more...

Your Price

$12.94

Uni Washer Upper Spin Bearing

★★★★★

1 Review

PartSelect Number PS473382

Manufacturer Part Number 5308002401

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Patrick from Humble, TX

Noisy spin cycle

1) Unplugged washer and disconnected the hot and cold hoses.
2) removed the 2 phillips screws at the bottom of the front panel then removed front panel, you need enough clearance by the floor, this is tricky because you have to lean washer back and push down on the front panel.
3) removed the agitator from the washer
4) lifted top of washer and leaned back against the wall and removed the splash tub cover one clip at a time with a flat screw driver.
5) removed the trunion, this is difficult and will take some time due to the corrosion from many years of use use a hammer (3Lb short handle) and tap one side then the other. You will need to rock it back and forth awhile.
6) lift the basket out of splash tub
7) I removed the hose for water level and removed the 3 bolts that hold the splash tub to the three base mounts (support arms).
8) remove the splash tub
9)change the plastic washer that is between the splash tub and the transmission in the bottom of the splash tub
10) change the bearing(metal sleeve) on the bottom of splash tub and lightly grease w/ a thin film of teflon grease
11) install splash tub and install the 3 bolts along w/ the water level tube
12) install the larger seal (w/ spring in it) and push into the splash tub firmly
13) use some tub and faucet silicone grease on the smaller seal because you don't want to damage this main seal, install the main seal (sits on top of the larger one that's in the tub already) be careful when getting to flat part of the shaft when installing ( spin around the shaft as you pass this point) it will keep the seal from coming out.
14) install trunion (sits down on top of the seal) you will feel the tension of the spring when bolting the trunion back into place.
15) install basket and bolt it to the trunion (I installed a new filter on the bottom of the basket and required some special glue, ask for "3M" GMGA600 adhesive.
16) installed splash tub cover, agitator and front cover.
Washer works great and is quieter than it was new. Read more...