Uni Dishwasher Hardware

Videos!

Your Price

$7.81

Uni Dishwasher Heating Element Brass Nut

★★★★★

8 Reviews

PartSelect Number PS1524878

Manufacturer Part Number 154106202

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step guide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.

Installation Instructions

Dennis from Tryon, NC

Water leaking under the dishwasher

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed. Read more...

Videos!

Your Price

$31.44

Uni Dishwasher Spring Linkage

★★★★★

2 Reviews

PartSelect Number PS420766

Manufacturer Part Number 154325201

This linkage attaches to the door spring.

Fixes these symptoms

Door latch failure
Door won’t close
See more...

Installation Instructions

Michael from Redmond, WA

One of the door tension springs and related plastic clip failed causing door to open under full weight

Per the recommendation from PartSelect.com, I purchased 2 new springs and 2 new clips - one set for each side. With the bottom cover plate removed below the door, I removed the remaining spring and clip and installed the 2 new springs and clips by hand. The door now opens with resistance and won't even stay completely opened unless the lower dishwasher tray is rolled out on it. it's like new.
This is the second repair to this dishwasher. Last year I replaced the door latch that had broken with a replacement purchased from partselect.com. That repair was also quite easy.
PartSelect's full part brochures by model made identifying the needed parts simple, and the replacement a breeze.
I even repaired my refrigerator ice maker a couple months ago after purchasing a new control module, and saving both a service fee and the probable full price for a new ice maker.
I've repaired my electric clothes dryer too, and hadn't even thought about all the repairs I'd done thanks to this website, until I told the story of my dishwasher.
I've probably saved $1000 already. Wow!
I love this site. Read more...

Your Price

$14.50

Uni Dishwasher Kit - includes 8 Screws & 8 Washers

★★★★★

2 Reviews

PartSelect Number PS470437

Manufacturer Part Number 5303943103

Use for the upper rack rollers on the upper rack of your dishwasher.

Installation Instructions

Terry from Pleasant View, UT

Top rack was dropping out of rollers/Slides

This was the second part of repair. Left side was constantly falling out of the slide. I replaced the same items as above minus the gasket and screw kit. Once done, the right side was sloppy so I orders part for that side plus gasket which slid right in.
1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket Read more...

Your Price

$7.13

Uni Dishwasher Door Catch Screw

PartSelect Number PS417465

Manufacturer Part Number 131302901

This is a shoulder screw and is used in conjunction with multiple appliances within your home. This specific model is size 10, and it has 16 threads to an inch. This part is made entirely of metal and is chrome-colored. The shoulder screw measures to be less than an inch long, and has a flat bottom and top. In general screws are typically made of metal, and the purpose of them is to be used as a fastener when attaching one piece/part to another. This model is sold individually.

Fixes these symptoms

Lid or door won’t close
Will Not Start
See more...

Installation Instructions

Denise from King, NC

Door Latch broke

First removed old piece, then put the new one on but didn't remove the wires until last to be sure they would be placed back right. Thats it, the dishwasher is back in business. Read more...

Your Price

$5.87

Uni Dishwasher Element Grommet

PartSelect Number PS451462

Manufacturer Part Number 5300806833

This grommet is used in a number of household appliances. Most often it is used in the dishwasher as part of the assembly that mounts and holds the heating element in place. This replacement part is made out of rubber, which helps create a seal between the element and the appliance. This grommet is sold individually. If you are replacing the heating element, or the brass nut that holds it in place, we recommend you replace the grommet at the same time. Before you begin any repair work on your dishwasher, make sure you have unplugged it and shut off the water supply.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Eric from Holly, MI

Water leaking from under dishwasher

Removed lower trim covers (2 Phillips screws) disconnected power supply at breaker box. Removed wire from heating element, removed (broken) brass nut, unclipped heating element and removed. Removed flat washers and replaced with new grommets. Kind of tricky getting them in there. Also had to lube them with silicone to get the element back through. Installed new brass nuts and installed wire connectors. Reset breaker and started diswasher to verify repair. No leaks, working just fine, reinstalled lower trim covers Read more...