Stump Grinder Hardware
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Stump Grinder Hardware
Your Price
$6.25
In Stock
Stump Grinder Washer 5/16 Std Flt
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
PartSelect Number PS16381824
Manufacturer Part Number 596134901
It is an authentic item that is supplied directly from the original equipment manufacturer for use with Husqvarna and Poulan lawn and garden equipment. A washer is generally utilized to provide a tight seal between connected parts, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this durable metal washer is sold individually.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair. HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Your Price
$6.25
In Stock
Stump Grinder Lock Washer
PartSelect Number PS16381888
Manufacturer Part Number 596238701
This is a genuine OEM replacement part used on a variety of Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. This steel washer has several applications based on your unit. Please refer to diagrams for proper application.
Your Price
$6.25
In Stock
Stump Grinder Screw-taptite
PartSelect Number PS9180925
Manufacturer Part Number 95-1726
This is a high quality replacement hardware that is specially manufactured for use on Toro lawn and garden equipment. Two of these screws are generally used to secure the belt guide to the mower deck. Please note this durable metal hex head taptite screw is included per order.
Your Price
$8.97
In Stock
Stump Grinder Washer-friction, Composit
PartSelect Number PS8843129
Manufacturer Part Number 114-0463
This is a genuine Toro replacement part. The friction washer is designed by the manufacturer for use in lawn tractors. This part is used to help secure the idler arm and apply friction to its motion. You will require a wrench when replacing this item. This part is sold individually.
Your Price
$6.25
In Stock
Stump Grinder Nut-lock, Ni
PartSelect Number PS9276436
Manufacturer Part Number 3296-29
The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has broken because the augur will not spin, and this is when the part should be replaced.
Customers found this to be an easy repair.
Your Price
$6.25
In Stock
Stump Grinder Washer-flat
PartSelect Number PS8954417
Manufacturer Part Number 3256-24
This flat metal washer fits onto the speed guide-selector and is available individually. Please note that more than one washer may be needed when replacing parts. It will need to be replaced if it becomes lost or broken and may require a wrench during installation. This is an OEM Toro part sourced directly from the manufacturer and used in snowthrowers.
Your Price
$6.25
In Stock
Stump Grinder Washer-flat
PartSelect Number PS8951750
Manufacturer Part Number 3256-3
This replacement flat washer is sourced directly from the original equipment manufacturer, it is specially designed for use with Toro riding lawn and garden equipment. It helps to distribute the pressure evenly between connected parts to ensure a tight fit, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable metal washer is sold individually.
Your Price
$6.25
In Stock
Stump Grinder Nut-flange, Ni
PartSelect Number PS8827741
Manufacturer Part Number 104-8301
This is a genuine OEM sourced hardware that is specifically made for use with Toro lawn and garden equipment. It is a standard hardware which may have multiple applications depending on the model of your unit. Please make sure to refer to the appropriate diagrams for the correct location and application of this part. Keep in mind this high-quality flange nut is made of durable metal and is sold individually. Note, you will need a wrench to secure or remove it.
Your Price
$6.25
In Stock
Stump Grinder Hcs 5/16-18 X 3/4
PartSelect Number PS16381777
Manufacturer Part Number 596030501
This hexagon head screw is a durable fastener designed for reliable use in outdoor power equipment such as lawn tractors, snow blowers, and similar machines. Made from high-quality high carbon steel, it provides the strength and stability needed to withstand demanding operating conditions. The screw measures 5/16-18 in thread size with a 3/4-inch length, making it ideal for securely fastening components and maintaining the structural integrity of your equipment. Its precise design ensures a dependable fit, helping to reduce loosening or wear over time. Whether you're replacing a missing or worn fastener, this heavy-duty screw offers a long-lasting solution to keep your equipment performing at its best.
Your Price
$6.25
In Stock
Stump Grinder Nut-lock, Ni
PartSelect Number PS8953555
Manufacturer Part Number 3296-42
This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut has broken when it appears to have damaged threads or rounded off edges.
Customers found this to be an easy repair.