Snow Blower Blades

Snow Blower Edger Blade This Edger Blade is a black, metal blade which is sold individually and comes certified from the manufacturer. Installation is rated as "Easy" and requires a socket set and wrench set. This blade attaches to the drive shaft and is used for edging the grass around driveways and walkways. If this part becomes worn/fatigued/damaged (which may happen after hitting the pavement) you will notice an odd vibration and poor trimming, at which time the part should be replaced.

Snow Blower Service Kit Scraper Bar

★★★★★

★★★★★

1 Review

This replacement scraper bar is an authentic item that is supplied directly from original equipment manufacturer for use with Husqvarna and Poulan snowblowers. Scrapers are designed to absorb a lot of friction while the machine is in operation. You can tell that a snowblower has a worn scraper because it will no longer be able to clear the sidewalk, leaving patches of snow behind. Please note this scraper bar is sold individually.

Snow Blower Blade-rotor

Snow Blower Scraper Bar This replacement scraper bar is an authentic OEM supplied item that is commonly utilized on Poulan and Husqvarna snow throwers. It is secured behind augers to scrape up the snow that is left behind. This durable metal item is sold individually, please note the hardware to secure this bar is sold separately. You should only need a wrench to replace this part.

Snow Blower Blade-rotor

Snow Blower Blade-scraper, Pc21 This is an original Toro replacement part. It is supplied directly from original equipment manufacturer for use with snow blowers/throwers. Snowblower scrapers absorb a lot of friction while the machine is in operation, and they are designed to wear down over time. You can tell that a snowblower has a worn scraper because it will no longer clear the sidewalk as well as it did before wearing. Please note, paddles and scrapers are designed to wear at approximately the same rate, so it's always a good idea to replace them both at the same time. This vinyl blade-scraper is sold individually. Replacing it is a quick and easy job. You will need a wrench to complete this repair. • Remove the scraper bolts • Pull the old scraper off of the snowblower • Press the new scraper onto the lip of the impeller • Return the scraper's bolts and nuts to their positions

Snow Blower Scraper Bar This is an authentic replacement part sourced from the original equipment manufacturer. This metal scraper bar is a component of the auger housing on Craftsman snow blowers. Over time this part may become worn, requiring replacement. While this part is not adjustable, it is reversible, allowing for longer usage. Please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. One item is included per order.

Snow Blower Blade- Scraper - 28-inch This replacement part is supplied directly from the original equipment manufacturer for use with Ariens snowblowers. The blade is secured in the back of the unit in order to scrape up any snow left behind. Scrapers are designed to absorb a lot of friction, generally, you can tell that a snowblower has a worn scraper because it will no longer be able to clear the sidewalk, leaving patches behind. Please note, paddles and scrapers are designed to wear at approximately the same rate, so it's always a good idea to replace them both at the same time. Keep in mind this high-quality 28" scraper blade is made of durable vinyl material and is sold individually. This part is made out of 10-gauge steel.

Snow Blower Blade, Scraper 27 H1 This is an authentic OEM part. The Craftsman scraper blade is attached to the bottom of the auger housing to protect the housing and augers on your snowblower. A socket wrench will be needed to remove the nuts to get access to the scraper blade. This part is made of metal and is sold individually.

Snow Blower Blade, Scraper This is a genuine part that is supplied by the original manufacturer for use with Honda snowblowers. The scraper blade attaches to the bottom of the auger housing, to protect the housing and augers from ice and other debris. This part is made of durable plastic and is sold individually. Before installation, be sure to remove the ignition key. You will need a socket wrench to aid you in this repair.