Snapper Chainsaw Hardware

Snapper Chainsaw Nut The OEM Mounting Bar Nut is a nut used to install a mounting bar to your machine. Installation requires a wrench set and socket set, and is rated as "Easy". This nut attaches to the chainbar studs.

Snapper Chainsaw Bar Adjustment Retainer This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on the screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.

Snapper Chainsaw Adjust Pin-bar 36/41 This Bar Pin Adjuster is an OEM part used to adjust the tension on the bar, which loosens or tightens the chain. It attaches to the slot in the bar, and the chainsaw bar adjusting screw. Installation is rated as "Easy" and requires a screwdriver. Refer to your make, model and diagram to ensure this part is correct.

Snapper Chainsaw Nut, Carb This is an authentic replacement part supplied from Poulan. It is generally used with gas powered chainsaws. This nut in conjunction with a bolt (sold separately) helps to secure air filter and carburetor. Requires a wrench installing/removing this item. It is sold individually.

Snapper Chainsaw Friction Disc Clutch 36/41 It is a genuine item that is supplied by the original manufacturer for use with Poulan and Weed Eater chainsaws. This washer-clutch is a special friction disk that helps to engage the clutch by ensuring a right fit between connected components. It provides an identical replacement for a damaged or a missing hardware that was installed on a new unit. Check the diagrams of your model for the exact location and the correct installation of this part. One durable metal washer-clutch is included. You may need a screwdriver and a wrench set to perform this repair.

Snapper Chainsaw Scrm4.8-1.6x This is a genuine OEM sourced replacement part designed for use with Poulan chainsaws. It is used to attach the cylinder shield to the main body of the chainsaw. This screw is made out of metal and it is sold individually. To remove or install this screw you would need a T-25 torx screwdriver.

Snapper Chainsaw Screw This replacement part is an authentic OEM screw designed for use with gas chainsaws and trimmers. This item is generally used to secure the housing of the equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

Snapper Chainsaw Washer-flywheel This is an original replacement part manufactured for use with chainsaws and leaf blowers. The washer is commonly used to disperse the pressure put on the flywheel by a nut across a wider surface area. This washer is available as an individual replacement part, please see model diagram for associative parts.

Snapper Chainsaw Bolt, Bar This is a genuine replacement part for Craftsman chainsaws. The bar bolt is designed to sit behind the bar mounting plate and gives a location for the bar to fasten to. The bolt is made from high-quality metal. Note you require two bolts to fasten the bar. This item is sold individually.

Snapper Chainsaw Gear-worm Spring This worm gear spacer is an OEM direct from Craftsman. Constructed of metal, this part is compatible with many chainsaw engines. The spacer is fitted on the end of the crankshaft, and has been designed to drive the oiler. Although this part is sold individually, it is often found in oil pump assemblies. A screwdriver and a wrench are helpful in the replacement.