Senco Compressor Parts

This rubber isolator foot helps reduce vibration and noise generated by an air compressor while providing a stable, non-slip base during operation. Constructed from durable hard rubber with an integrated metal core, it absorbs motor vibration and helps prevent the compressor from shifting or "walking" across the floor, protecting both the equipment and the supporting surface. Replacing a worn, cracked, flattened, or damaged isolator foot can restore stability, improve vibration dampening, and help extend the life of the compressor by reducing stress on the frame and mounting components. This replacement foot is sold individually and includes the mounting screw required for installation. Installation is straightforward and typically requires only a screwdriver to remove the old foot and secure the replacement in place. For best results, inspect the remaining feet and mounting hardware for wear or damage and replace additional components as needed to maintain proper compressor stability and support.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Senco electric air compressors. A check valve is an important safety feature that will release excess pressure from the tank. If the valve is damaged or missing it should be replaced to ensure safe and proper operation of your unit. One durable metal check valve is included. Refer to the owner's manual and the diagrams of your model for the correct application of this component. You will need a wrench to secure and remove this check valve.

This part is an OEM sourced directly from the manufacturer for use in Senco compressors. The pressure regulator is made out of metal and plastic. A wrench may be needed during the replacement of this part. It may become broken and will need to be replaced. This item is sold individually.

This is a Genuine Manufacturer Approved replacement part designed to work with Senco Air Compressor. The pressure switch tells your compressor when to stop and when to start. There are multiple reasons a Pressure Switch could be leaking air. If it is leaking air the Pressure Switch should be replaced for a compressor to operate properly and safely.

The metal compression spring is made of metal and goes between the check pawl and the door. This part is available as an individual replacement and is an OEM replacement part from the manufacturer Bostitch for use in nailers. Springs can lose their tension over time and will need to be replaced. A set of pliers and a socket set may be needed when replacing this spring.

Genuine Senco replacement part used on specific Air Compressor, this item is sold individually. This compressor Regulator is used to regulate the air pressure in the compressor tank. It is also used to regulate the air pressure of the air exiting the tank. In some instances you will need to lower or higher the air pressure of the tank and the air coming from the tank.

This is a genuine Senco replacement pressure gauge. It is specially designed for use on electric air compressors. The gauge registers pressure readings and allows you to maintain needed pressure. The dial on this gauge reads 0-160 PSI. It has a durable metal body and it is sold individually. To complete this repair job you will need an adjustable wrench. • First make sure the compressor is unplugged • Depressurize the tank • Remove the manifold cover • Remove the old pressure gauge • Install the new pressure gauge • Secure the manifold cover • Test the new gauge

It is a genuine OEM supplied item that is made for use with Senco air compressors. This is an identical replacement for damaged or a missing component that was installed on a new unit. Check the diagrams for your model to ensure the correct repair procedure. Keep in mind this high-quality exhaust valve assembly is made of durable materials and is sold as an individual item. A properly sized Allen wrench will be needed to replace this component.

This drain valve is an authentic OEM part that is designed for use with Senco electric air compressors. The drain valve is used to release the air from the tank to ensure that condensation does not occur. A rusted or corroded drain valve should be replaced to maintain top performance. This item includes one metal valve along with a rubber o-ring and it is sold individually. A wrench is needed to replace this piece of hardware.

This authentic OEM approved replacement part is supplied from original equipment manufacturer for use with Senco air compressor. This filter is designed to clean air coming into the pump. To ensure the pump continually receives a clean, cool, dry air supply this filter must always be clean and ventilation opening free from obstructions. This filter is made out of foam material with a plastic holder. Includes one (1) filter per order.