This temperature sensor, also called a thermistor, measures temperature inside the refrigerator or freezer and sends readings to the main control board. The board uses this information to control cooling, including compressor and fan operation. Incorrect readings may cause the compartment to become too warm or too cold, or make cooling ru...Read moren longer than needed. The replacement includes the sensor body and wire leads. Its location varies by appliance. This is an OEM part sourced directly from the manufacturer.
This NSF-certified water filter helps to improve the taste, quality, and health of your water by removing a number of contaminants including mercury, lead, and trace pharmaceuticals. The filter should be replaced every six month or after 300 gallons of water have been filtered. If you are unsure if your filter is due for replacement, anot...Read moreher indicator is if the water flow from the dispenser has slowed down considerably. Replacing this part is a simple task that does not require any tools or shutting off the water or power supply to your fridge. Once the new filter has been installed, be sure to run at least two gallons of water through before consuming.
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the switch. The switch is spring loaded and is a generally closed type of switch meaning there should be no continuity when the button is depresse...Read mored, and continuity through the switch when the button is not depressed. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat blade screwdriver and needle nose pliers.
Support steady compressor operation with this refrigerator run capacitor. It provides the electrical phase shift needed for the compressor motor to run properly as the cooling system operates. A failing capacitor may contribute to humming, difficulty starting, interrupted compressor operation, or rising compartment temperatures. Visible s...Read morewelling, leaking, or burned terminals may also indicate damage. Unplug the refrigerator before accessing the component. Capacitors can retain an electrical charge after power is disconnected, so follow approved discharge procedures and avoid touching or shorting the terminals. Record the wire positions before replacement. This is an OEM part sourced directly from the manufacturer.
This gallon-sized refrigerator door shelf bin is a genuine OEM replacement designed for select General Electric (GE) models, including compatible units from Hotpoint and Café. Constructed from durable, food-grade clear plastic with a white band along the top, it offers a transparent view of stored items and supports efficient organization...Read more of beverages, condiments, and jars. Designed for installation on the right-side door, this bin replaces several previous part numbers and is intended for tool-free installation. Some versions may include a bonus soda can organizer. Always verify your refrigerator’s model number to ensure compatibility before purchase.
Brighten the fresh food compartment with this refrigerator LED light and cover assembly. The built-in light board illuminates stored food, making containers, labels, and items at the back easier to see. Its cover holds the light in place and helps protect the components from accidental contact. A failed module may cause dim lighting, flic...Read morekering, or a dark section inside the refrigerator. Replacing a faulty assembly helps restore clear, steady lighting. Unplug the refrigerator before disconnecting the old module or installing the replacement. This is an OEM part sourced directly from the manufacturer.
This is the glass drawer cover insert for models of refrigerator. This glass pane is used as a shelf and cover that lays on top of the drawer below it. If this glass is missing or damaged in any way, it will need to be replaced. To replace this glass drawer cover, simply lift the old one out from underneath, and lay the new one in. This g...Read morelass pane measures 30-inches long by 10-inches wide, and is an OEM part for your fridge, so it is not sold with any other parts or accessories.
Frost buildup can mean the freezer door gasket needs replacement. It seals the door opening to help keep cooled air inside. This OEM gasket is listed for select refrigerators; check your appliance model number to confirm compatibility.
A warm fresh food section or fan noise can be a symptom of a failing fan motor. This OEM axial fan motor circulates air through the refrigerator fresh food section to improve cooling. It has a wire lead and is rated at 13.6 VDC and 0.17 A. Check the refrigerator model information to confirm fit.
While you wait for a replacement water filter, a white bypass plug lets your refrigerator operate without one. Check your refrigerators model number to confirm fit. It is an OEM part.
A refrigerator control-board fault may be associated with temperature fluctuations, ice dispensing problems, or an unresponsive display. This OEM main control board regulates temperature, ice production, defrost cycles, and fan operation. Check your refrigerators model number to confirm compatibility.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
my refigerator was warm but the freezer was cold and working correcttly
305 of 405 peoplefound this instruction helpful.
michele from North Smithfield, RI
Really Easy
15 - 30 mins
Pliers
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.
I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more />After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.
I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
Read less
Was this helpful?
Thank you for voting!
refrigerator was getting too cold
149 of 219 peoplefound this instruction helpful.
Larry from Menomonie, WI
A Bit Difficult
15 - 30 mins
I removed the old temperature sensor by cutting the wires. I attached the wires of the new sensor with wire nuts and mounted it in the same bracket.
Was this helpful?
Thank you for voting!
Sticking Light Switch
122 of 178 peoplefound this instruction helpful.
Jonathan from Lilburn, GA
Really Easy
Less than 15 mins
Pliers, Screw drivers
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the c
... Read moreatch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.