EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

ZSGW420DMD General Electric Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Ice and Water Filter – Part Number: MWFP
$74.23
In Stock
Refrigerator Ice and Water Filter
★★★★★
★★★★★
(82)
Part #MWFP
This ice and water filter helps reduce impurities in select side by side and bottom freezer refrigerators. Replace it about every six months, or when water flow slows, ice production drops, or the filter light turns red. Some older filter setups may need an adapter. Place a cloth under the filter before removal. Check the exact refrigerator model before ordering.
Temperature Sensor – Part Number: WR55X10025
$30.53
In Stock
Temperature Sensor
★★★★★
★★★★★
(69)
Part #WR55X10025
This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too cold, or not defrosting properly, then there may be a problem with your sensor. The temperature sensor can break from material fatigue or through normal use, and should be replaced. It is attached to the evaporator and control housing in your appliance. It measures approximately 1.25 inches long with 18 inch wire leads, and is constructed out of plastic. This part comes in white, beige. It includes the sensor, with wire leads.
Dispenser Door Assembly or Flapper – Part Number: WR17X11653
$33.60
In Stock
Dispenser Door Assembly or Flapper
★★★★★
★★★★★
(93)
Part #WR17X11653
This “Dispenser Door Assembly” (Door Recess Assembly, Ice Door Assembly, Dispenser Door, Refrigerator Dispenser Ice Chute Door Kit, Dispenser Door Flap, Ice Chute Door, Flapper) keeps the room air from infiltrating the freezer. Once the lever is pressed, the door flap opens and allows the ice to dispense into your container. If your door flapper is broken, it could allow outside air to enter the freezer and alter the inside temperature. You may notice frost buildup surrounding the dispenser area. The door flap can disconnect from the dispenser lever, or the tabs that hold it in place may break. Frequent use may distort the sealing face and cause air leaks and frost buildup. This part mounts in the ice dispenser, and measures approximately 3.25 inches in diameter. It is constructed of plastic and rubber, and comes in white/black. This part is sold individually.
Evaporator Fan Grommet - Red – Part Number: WR02X12008
$13.92
In Stock
Evaporator Fan Grommet - Red
★★★★★
★★★★★
(27)
Part #WR02X12008
If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter. The evaporator fan grommet is located behind the evaporator fan cover in the back of the freezer. You will need to remove the evaporator fan cover to access the evaporator fan and complete this repair. Before you begin this repair, ensure the power to the refrigerator is disconnected. You will need a pair of needle nose pliers, a small flat blade screw driver and both a 1/4 and 5/16-inch nut driver to complete this repair.
Dispenser Door Solenoid Assembly – Part Number: WR62X10055
$56.33
In Stock
Dispenser Door Solenoid Assembly
★★★★★
★★★★★
(36)
Part #WR62X10055
This genuine OEM solenoid is designed for use with GE refrigerators and controls the opening and closing of the ice chute door. It serves as a direct replacement for a worn or faulty solenoid, helping to restore proper ice dispenser function. Constructed from durable metal, this part includes all necessary wiring for installation and is sold individually. Installation requires a Phillips screwdriver. Always refer to your appliance’s manual or diagram to ensure proper placement and compatibility before beginning the repair.
Union Connector - 5/16 Inch to 5/16 Inch – Part Number: WR02X11330
$15.00
In Stock
Union Connector - 5/16 Inch to 5/16 Inch
★★★★★
★★★★★
(11)
Part #WR02X11330
Quick connector for plastic water line - 5/16" to 5/16"
DISPENSER LIGHT – Part Number: WR01X37886
$35.22
In Stock
DISPENSER LIGHT
★★★★★
★★★★★
(19)
Part #WR01X37886
This twelve volt dispenser light bulb is a little under two inches long.
LIGHT SWITCH – Part Number: WR23X37285
$38.32
In Stock
LIGHT SWITCH
★★★★★
★★★★★
(65)
Part #WR23X37285
The interior light of your refrigerator is controlled by a switch that is activated when the door is opened and closed. If your refrigerator light will not turn on, there could be an issue with the switch. The switch is spring loaded and is a generally closed type of switch meaning there should be no continuity when the button is depressed, and continuity through the switch when the button is not depressed. This plastic, white, OEM switch is sourced directly from the manufacturer, is sold individually and is easy to replace. The repair usually takes less than 15 minutes and requires a flat blade screwdriver and needle nose pliers.
Evaporator Fan Motor – Part Number: WR60X10185
$83.64
In Stock
Evaporator Fan Motor
★★★★★
★★★★★
(22)
Part #WR60X10185
This evaporator fan motor circulates air to the fresh food compartments for efficient cooling. It powers the evaporator fan that draws air from the refrigerator and circulates it over the evaporator coils. Your fan motor has a long life cycle, but can burn out quickly if there is an obstruction preventing the fan from rotating. If the fan does not operate, the freezer will not cool properly. This will affect the performance of the compressor. This evaporator fan motor is located in the back of the freezer section of your refrigerator, behind the auger motor assembly. It is attached to the back wall. If you notice problems with your freezer then check to see if there is anything blocking a fan blade. If there is no obstruction, test the evaporator fan motor using a multimeter. Test the 2 wires that travel from the coil on the motor for resistance. If these tests indicate that the evaporator fan motor is at fault, it must be replaced. This part features 1 evaporator fan motor, which is metal and plastic, and comes in white/silver
Lid Bumper – Part Number: WR02X10540
$16.05
In Stock
Lid Bumper
★★★★★
★★★★★
(2)
Part #WR02X10540
The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.
Dispenser Door Recess Crank – Part Number: WR17X10706
$16.05
In Stock
Dispenser Door Recess Crank
★★★★★
★★★★★
(1)
Part #WR17X10706
This crank door recess is supplied directly from the original equipment manufacturer. The plastic part is fastened behind the interface dispenser assembly in the freezer door. Activated by the dispenser solenoid, this part regulates the opening and closing of the ice chute door. A screwdriver is needed for the repair. The crank door recess is sold individually.
Refrigerator Bypass – Part Number: WR17X22070
$15.28
In Stock
Refrigerator Bypass
★★★★★
★★★★★
(9)
Part #WR17X22070
This part is a replacement filter bypass cap for your refrigerator. If you intend to use an external water filtration system for your refrigerator, the bypass cap will allow you to do so. To use a filter bypass cap, simply screw it in where you would normally screw in the regular water filter. If you have a bypass system installed and your ice maker doesn’t make ice, your water dispenser doesn’t make water, or if there is water dripping inside your refrigerator, you may need to replace the bypass filter cap. This part is made of white plastic and is sold individually.

Common Symptoms of the ZSGW420DMD

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
my refigerator was warm but the freezer was cold and working correcttly
305 of 404 people found this instruction helpful.
  • michele from North Smithfield, RI
  • Really Easy
  • 15 - 30 mins
  • Pliers
I went to a GE repair center to explain my problem, the service center reccomended that I have a techinician come out o look at it. $75.00 for the visit and what ever labor and materials wuld cost.

I went on line to see if there were others having this same problem and found that there were many with the same problem.
... Read more />After reading some of the ways that people found out what was wrong ...it became a matter of three components, the timer, heater or thermostat.

I tried the most common component and the less expensive one first , the thermostat switch I installed it very easily snipping two wires and attaching the news using wire nuts I used the diagram on this website to pinpoint the component and there has not been a problem since.
Was this helpful?
Thank you for voting!
Replace water filter
226 of 350 people found this instruction helpful.
  • Alfred from Novato, CA
  • Really Easy
  • Less than 15 mins
Unscrew old filter and remove(counterclockwise). Line up arrow on new filter with arrow on connection housing. Turn clockwise till resistance met. Do not overtighten. Follow directions. Simple.
Was this helpful?
Thank you for voting!
refrigerator was getting too cold
149 of 218 people found this instruction helpful.
  • Larry from Menomonie, WI
  • A Bit Difficult
  • 15 - 30 mins
I removed the old temperature sensor by cutting the wires. I attached the wires of the new sensor with wire nuts and mounted it in the same bracket.
Was this helpful?
Thank you for voting!