This ice and water filter helps reduce impurities in select side by side and bottom freezer refrigerators. Replace it about every six months, or when water flow slows, ice production drops, or the filter light turns red. Some older filter setups may need an adapter. Place a cloth under the filter before removal. Check the exact refrigerator model before ordering.
This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in c...Read moreonnectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.
The water inlet valve on your refrigerator allows water to enter the ice maker and water dispenser. If your ice maker or water dispenser is not functioning properly, or you notice a leak, you may need to replace the single outlet valve. This single outlet valve has 1/4-inch compressions fittings and is intended for use with refrigerators ...Read morethat make crescent-shaped ice cubes. As per the manufacturer, this valve has a new quick connection. You must cut the retaining nut off your current plastic water line, and gently push it into the new valve. Be sure to disconnect the water and power sources from the refrigerator before you begin this repair.
This evaporator fan motor circulates air to the fresh food compartments for efficient cooling. It powers the evaporator fan that draws air from the refrigerator and circulates it over the evaporator coils. Your fan motor has a long life cycle, but can burn out quickly if there is an obstruction preventing the fan from rotating. If the fa...Read moren does not operate, the freezer will not cool properly. This will affect the performance of the compressor. This evaporator fan motor is located in the back of the freezer section of your refrigerator, behind the auger motor assembly. It is attached to the back wall. If you notice problems with your freezer then check to see if there is anything blocking a fan blade. If there is no obstruction, test the evaporator fan motor using a multimeter. Test the 2 wires that travel from the coil on the motor for resistance. If these tests indicate that the evaporator fan motor is at fault, it must be replaced. This part features 1 evaporator fan motor, which is metal and plastic, and comes in white/silver
The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side brack...Read moreet on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.
This DC fan motor moves air across the condenser coils and compressor to help remove heat. A failed motor may cause poor cooling, a hot compressor, or humming and squealing sounds. Before replacing it, clean the coils and check the fan blade, wiring, and air path for dirt or damage. Confirm fit with the full appliance model, 4-pin plug, a...Read morend 11.3- to 12-volt rating. Unplug the refrigerator before removing the rear panel. Keep hands away from the blade, protect the cooling lines, and reinstall the panel before testing the unit.
This plastic door bin is designed to attach securely to the inside of your refrigerator door, providing convenient storage for bottles, jars, and other small items. Its adjustable placement allows you to customize your storage space as needed. The bin features a white base with a clear exterior and measures approximately 16 inches wide, 5...Read more inches high, and 5.5 inches deep. If the bin is cracked or the mounting tabs are broken, replacing it will restore proper function. This part is sold individually.
If your freezer drawer isn’t sealing right, this gasket could be the fix. It helps keep cold air in and warm air out, preventing frost and keeping food fresh. Made to fit GE bottom freezer models, it’s flexible, durable, and easy to install—just pop out the old one and press in the new.
Bottles that lean or a shelf that rattles may indicate a damaged right-hand door bin. The deep bin adds storage inside the refrigerator door for jars, drinks, and other upright containers. Check whether the bin itself is cracked or whether the mounting slots in the door liner are broken. Verify fit with the full appliance model before ord...Read moreering, since left- and right-side bins are not always interchangeable. Remove all stored items before lifting the old bin free. Clean the mounting area with mild soap and dry it fully. Set the replacement tabs into their matching slots, lower the bin evenly, and give it a gentle pull to confirm that it is secure before loading it.
A door bin that sags, rattles, or falls from the refrigerator door may have broken tabs. This clear, deep bin holds bottles, jars, and small food containers inside the fresh food section. First check whether the damage is on the bin or on the door itself. A new bin will not stay in place if the door slots are cracked. Use the full applian...Read morece model number to check the size and mounting shape. Remove all food before taking out the old bin. Clean the mounting area, place the new bin over the supports, and press it down gently. Test the fit before loading it, and keep very heavy items on a shelf.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replace water filter
226 of 350 peoplefound this instruction helpful.
Alfred from Novato, CA
Really Easy
Less than 15 mins
Unscrew old filter and remove(counterclockwise). Line up arrow on new filter with arrow on connection housing. Turn clockwise till resistance met. Do not overtighten. Follow directions. Simple.
Was this helpful?
Thank you for voting!
Evaporator motor sounded like wind in the trees howling
112 of 139 peoplefound this instruction helpful.
DOUG from MARYSVILLE, OH
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers
I had to remove all of the shelves.....part of the ice maker.....the rear cover over the freezer coils.....There were two wires that came from the back of the freezer that were also incorporated with the fan motor plug from the factory....This caused me to cut all of the wires from the new motor and soider them to the existing plug and sh
... Read morerink wrap the connections. If GE would have supplied two new ends I could have cut only those wires added the ends and inserted them into the new motor plug thus eliminating an extra hour and a soildering iron,,,,In my case not a big deal however not a project for those who have trouble with repairs using these type of tools.
Read less
Was this helpful?
Thank you for voting!
Warm freezer and no ice
95 of 134 peoplefound this instruction helpful.
Paul from Suwanee, GA
Easy
30 - 60 mins
Nutdriver
This story starts with a GE side-by-side refrigerator that has always had wide temperature swings and a temperamental water dispenser. The ice maker was not making ice, and the built in digital thermometer showed it was running warm. I suspected that the heat exchanger was full of dust and so looked there. What I found was that the con
... Read moredenser tank was hot to the touch and the fan wasn’t running. As an experiment, I aimed a fan at the it for a while I saw that the freezer temperature dropped back to normal. .The fan is marked as 11.2 DC so I checked for voltage at the fan and found some. With three wires and no wiring diagram I wasn’t sure this answered all the questions, but hooking the fan to a 12 volt power supply didn’t get it to spin. I priced parts at a couple websites before using partselect.com . They also have a good diagram to look at (Sears diagrams are really poor). I ordered the part with 2-day shipping; it arrived on time, was correct and fixed the problem.