ZET3038SH4SS General Electric Wall Oven - Instructions

Replaced High Voltage Diode. Very carfully due to the extream danger of a electrical shock.

It wasn’t the magnetron.
It wasn’t the diode.
It wasn’t just the fuse.
It was the High Voltage Capacitor (HVC). You know, the very thing they warn you about when opening the microwave. Just remember to discharge it using needle-nose pliers before probing around to find the problem. I also suggest you invest in a multimeter ... Read more so as not to waste hundreds of dollars like I did; that way you can go straight to the real problem instead of replacing symptoms. If you replace the HVC, you will also want to replace the two fuses right in front of it. Also, there is a wiring diagram and a troubleshooting flowchart tucked behind the front console near the top. It is extremely useful!

Pull the old one put in the new one ... took about 20 minutes

must of had loose connection from wire terminal
to thermostat from factory. thermostat and wires
were melted. removed thermostat. and cut burnt
wires back. replaced thermostat and terminals.
used better quality terminals than factory.
also checked and tightened other loose connections. there was enough wire left ... Read more after cut back to just put on new terminals.

This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.

- remove door from range following the basic guide to removing any range door.
- place door on work surface with the outside facing down.
... Read more - remove three 1/4 socket screws from bottom and two star screws on top.
- Flip door over, remove outer door panel and set aside.
- There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside.
- Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed.
- Remove the remaining 1/4 screws holding the aluminum shielding.
- Remove the shielding being careful not to disturb the insulation around the window.
- Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom)
- Set the new window in its place.
- Reverse the process by replacing the aluminum shield, hinges, than internal glass pane.
- Set outer door on top and holding everything together, flip door.
- Tighten the two star screws on top and the three 1/4 socket screws on the bottom.
- Replace door. Don't forget to lift up those hinge tabs before trying to close the door.
All done. Pat yourself on the back for a job well done.

Per instructions on part select.com website. But needs further repair because still doesn't heat food and pad is partially disabled.

turned off power to oven; pulled out old bulb (unscrewed glass cover to access). Noted the direction of the electrical prongs when pulled bulb out... and inserted new bulb. Turned back on power to oven - bulb worked

I'm well past ninety and my sweet daughter inserted the tiny prongs. I was delighted to find a place that had the bulbs. Thank goodness for the internet ! (I'm not too old for that)

Very easy to remove the parts and to reassemble

Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.

First, I turned off the power. I removed the fixture that held the bulb and gently used narrow type pliers to pull the old pins out and allowed the broken glass to fall upon a shop towel in the bottom of the oven.

The replacement bulb and different type of wiring connections. I cut and formed them to fit the receptacle. I gentl ... Read more y inserted the new bulb, placed the glass cover back on. Then, screwed the unit back into the top of the oven.

Happily, when power was turned back on the light shone brightly!

REMOVED 2 SCREWS AND LOWERED LIGHT ASSEMBLY. UNPLUGGED THE OLD ONE, AND REPLACED IT WITH THE ITEM SENT TO ME

Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.

Removed outer case, checked fuse first, it was good so went to thermostat. No continuity reading. Unhooked thermostat, used jumper wires to by-pass break—briefly plugged the unit in. It came on so I knew the issue was definitely the thermostat.

First of all, there are FOUR panes of glass on the oven door and two different sizes. Make sure you're ordering the right pane. We initially got the wrong one and had to return/reorder.

Took door off hinges and set on table. Removed almost all screws. Two at the top are very long and almost spring loaded -- this was helpful whe ... Read more n putting it back together.
When removing the layers, keep track of what/where screws are placed. Some are star-hole-head, some are hex-head (socket). Work slowly and carefully so as not to break additional panes of glass. Leave plenty of room in your workspace to set items aside while you get to the innermost part of the door.

For this part #, it's deep in the door layers and surrounded by fiberglass. Wear gloves so you're not itchy later. This part acts as a double-pane with a narrow aluminum frame around the two pieces of glass. Be careful not to bend the frame when removing the broken piece. One corner of the frame also has a hook-n-hole closure. Take care to not bend the hook too much.

We wiped all the glass pieces off to get all fingerprints, smudges, and baked-on foods removed. Then we put the pieces/parts back -- a lot like a puzzle. Had the oven back up and running with no problems. It may take two people to get the door back on the hinges just because of the weight and awkward position they need to clamp back together.