ZBD7100G01SS General Electric Dishwasher - Overview

Diagrams for ZBD7100G01SS

See every part. Know exactly what you need.

Parts for the ZBD7100G01SS

$44.23

Water Inlet Valve

★★★★★

(56)

Part #WD15X10014

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve open and close according to the desired amount of water needed.

$19.50

CLAMP

Part #WD01X24246

Rear Basket Insert

Part #WD28X10084

Sold individually.

Upper Dishrack Wheel

Part #WD12X10032

This wheel is sold individually. It comes with an attached axle.

Bottom Door Seal

★★★★★

(1)

Part #WD27X10091

Front Basket Insert

Part #WD28X10085

Sold individually.

$139.80

Silverware Basket Assembly

Part #WD28X10026

Door Seal

Part #WD01X10120

It provides a seal between the tub and the door.

Fold Down Clips - Set of 2

Part #WD01X10046

These clips are sold in a pair. They are used in conjunction with the front and rear inserts for the lower dishrack.

INSERT FRONT Right Hand

Part #WD30X10013

$63.64

INSERT REAR Right Hand

Part #WD30X10015

WHEEL & AXLE L/BASKET

Part #WD01X10047

Questions And Answers for ZBD7100G01SS

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:

Linda - For model number ZBD7100G01SS

January 14, 2020

Why would my panel board to start dishwasher just go dead and stop working? I seldom use dishwasher since it is in my vacation condo in las vegas . So it is just like new and seldom has been used.

Hello Linda and thank you for writing. There could be a few reasons, did you check that you have power to your unit as your breaker in the panel box might have tripped? If that checks our ok, we suggest to try a hard reset: Go to your breaker box and shut the breakers for your unit off, wait 5 minutes and then turn the breaker to on again. That should hopefully clear this problem. If this does not fix this problem then your switch latch PS651673 might be faulty and possibly needs to be replaced. And last it might be the control board itself PS651672 gone defective (possible power out could short the board).We hope this helps. Please contact us anytime.

$766.70

BOARD CONTROL & UI Assembly

$131.70

SWITCH O/CENTER LATCH

Was this helpful?

Common Symptoms of the ZBD7100G01SS

How this model fails, and the parts that fix it.

Leaking

Fixed by
these parts

Show All

Will not fill with water

Fixed by
these parts

Show All

Not cleaning dishes properly

Videos related to the ZBD7100G01SS

Watch our pros, then fix it yourself.

Replacing the Water Inlet Valve

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Water leak, small puddle to front left of dishwasher

65 of 85 people found this instruction helpful.

Greg from Burlington, VT
Easy
15 - 30 mins
Nutdriver, Socket set

You'll need to remove the front toe kick and (if installed, the GE Profile baffling for additional silencing action).

You will need to disconnect the right wire connection to access the right screw (and may need to use a flat head screwdriver). You can then remove the 2 screws that hold the Valve Water Inlet on.

... Read more

Read less

Was this helpful?

Leaking water when in use.

16 of 22 people found this instruction helpful.

J from Walnut, CA
Easy
1- 2 hours
Pliers, Screw drivers, Socket set

Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.

Was this helpful?

Dishwasher was leaking.

11 of 19 people found this instruction helpful.

James from Grand Isle, VT
Really Easy
15 - 30 mins
Nutdriver, Pliers, Screw drivers

Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.

Then reversed these steps and I was done.

Was this helpful?