Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YRED4300SQ0

YRED4300SQ0 Roper Dryer - Overview

Get Parts and Repair Help for YRED4300SQ0

If you know the dryer repair part you need, you can browse the list of all parts on the YRED4300SQ0, or you can search by name or part description. You can also find your part by where it is located on the YRED4300SQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YRED4300SQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for YRED4300SQ0

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.98

Thermal Fuse

This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty...

Order within the next 11 hrs and your part ships today!
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the motor rotates, the belt begins to move and turns the drum. If you notice the drum of your dryer is not spinning during the dry cycle, but you hear the motor running, your belt may have snapped and it will need to be replaced. This belt features four ribs and three grooves, however it replaces a wide variety of belts including wider styles that had five ribs and four grooves. When installing this part make sure the grooves are facing down, against the drum. This replacement part is 92 1/4 inches in length, and 1/4 inch wide. Before you begin any repair work, make sure your dryer has been unplugged.

Order within the next 11 hrs and your part ships today!
$14.96

Thermostat, Internal-Bias

A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees...

Order within the next 11 hrs and your part ships today!
$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer door closed. This kit includes two strikes, three catches, and a set of instructions. Each of the door catches included have a different tension. Make sure you use the one that matches the existing catch on your appliance. All three of these are color-coded, and have a number on the back. The instruction sheet will tell you which catch you need to use for your specific model type.

Order within the next 11 hrs and your part ships today!
$35.86

Thermal Cut-Off Kit

The thermal cut off turns off the heating component when the dryer overheats, ensuring there is a consistent level of heat at all times. This dryer thermal cut-off kit includes one...

Order within the next 11 hrs and your part ships today!
$42.85

Maintenance Kit

This maintenance kit or dry repair kit is used for dryers. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. If your dryer is making loud, squeaking, and squealing noises while the drum is turning, or the drum has stopped turning, using this maintenance kit is the solution. The tools needed for this installation project are: putty knife, Phillips screwdriver, 5/16 nut driver, and a small flat blade screw driver. This kit can be used for gas and electric dryers. Remember to unplug the dryer from the power source before beginning this project.

Order within the next 11 hrs and your part ships today!
$12.47

Rear Drum Support Roller Kit

The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings and one palnut (or retaining wash...

Order within the next 11 hrs and your part ships today!
$10.69

Thermostat, High Limit 221 F (

This hi-limit thermostat with Terminal Extension Arm acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches 221 degrees Farenheit, this piece will shut down power to the heating element until it drops by 80 degrees Farenheit.

Order within the next 11 hrs and your part ships today!
$10.04

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not s...

Order within the next 11 hrs and your part ships today!
$5.76

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

Order within the next 11 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2137 of 2405 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

Dryer tub belt broke

  • Customer: Ray from Denton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 853 of 905 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more

No Heat

  • Customer: Vernon from Niceville, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 820 of 869 people found this instruction helpful
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off. read more