Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YKGST307HB3

YKGST307HB3 KitchenAid Range - Overview

Get Parts and Repair Help for YKGST307HB3

If you know the range repair part you need, you can browse the list of all parts on the YKGST307HB3, or you can search by name or part description. You can also find your part by where it is located on the YKGST307HB3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for YKGST307HB3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for YKGST307HB3

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.80

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$52.58

Inner Door Glass

This inner door glass is used in ranges. It creates a transparent heat barrier inside your oven door. For this installment, the only tool needed is a #2 Phillips screwdriver. To repair, first remove the oven door from the range by lifting and pulling from the bottom of the hinges. To dissemble the door, you will need to remove the screws on the outer edge and remove the side pieces. There are also screws towards the middle that need to be removed to pull out the bottom trim. Next, lay the door on its back and slide outer door glass off and remove top trim. For the rest of the installation instructions refer to the manual provided by the manufacturer. Pro tip: remember to wait until the surface is cool before starting this repair project.

$4.12

Torx Screw

7-18 x 3/4" - sold individually.

$31.06

Temperature Sensor

This temperature sensor is used to measure the inside temperature of a self-cleaning oven. Its 1000-ohm resistance increases with temperature. The sensor has male leads, is 6 inches in length, and comes with 2 ceramic wire nuts. Fault temperature sensors are often responsible for F3 and F4 error messages on an electric range. Furthermore, if you find your oven is too hot, will not heat evenly, or simply will not heat at all, there could be an issue with your temperature sensor and you should look to replace it immediately.

$4.07

Screw

This screw is sold individually.

$31.67

Light Socket

The light socket on your electric range connects the power source to the light bulb. If your oven light is malfunctioning, you may need to replace the light socket. The light socket is located in the back of your range, so in order to access it you will need to remove the back panel. Many of our customers have rated this repair as easy, and it should take less than 15 minutes. Before you begin this repair, make sure to disconnect the power source from your range. This is an OEM part sourced directly from the manufacturer.

$23.78

2 Piece Broiler Pan

This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high tem...

$4.63

Light Gasket

This part creates a seal around the light lens and bulb.

$7.38

CLEANER

This bottle of non-abrasive cooktop cleaner breaks down and gets rid of the hardest baked-on stains and residue without causing any harm to your appliance. The bottle is 10 oz and ...

$5.54

Bumper Pad Set of 4

***NOTE: This part has been substituted by the manufacturer and may not appear the same as the original but should function the same. These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 142 of 181 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

Inside door glass broke

  • Customer: MANNY from LIVERMORE, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 113 of 124 people found this instruction helpful
I removed the oven door by lifting it off with the hinges. Disassembled the door parts one at time making sure I remember where I removed the screws until I am able to get to the broken glass. The most difficult part is making sure that the insulation strip & the gasket stayed in place after I replaced the broken glass & doing the reverse process of installi... read more

Oven stopped working/Slow to ignite

  • Customer: John from Chicago, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 49 of 53 people found this instruction helpful
Although the ignitors glowed brilliant yellow I learned from an expert there are 2 fail modes. 1. that they break and don't glow well enough to ignite the gas or 2. they get resistive over the years and do not pass enough current to open the valve. This is important to know because the current passes through the ignitor before it gets to the valve. If the... read more