EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

Y6020-WK (1) DeVilbiss Compressor - Overview

Diagrams for Y6020-WK

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
DRAIN VALVE – Part Number: N286039
No Longer Available
DRAIN VALVE
★★★★★
★★★★★
(1)
Part #N286039
Frequently referred to as a Drain Plug, this Drain Valve is used to drain any condensation that has collected inside the tank to prevent the tank from rusting. It is not part of a kit or assembly, is sold individually, made of brass, is gold, and will be found at the bottom of the air tank. This part will need to be replaced when it is no longer able to provide a proper seal, or if it is visibly worn or damaged. You will need a wrench to complete this repair. Customers rate this repair as Easy.
AC CORD – Part Number: D26615
$48.88
In Stock
AC CORD
Part #D26615
This power cord is a genuine high quality item, it is not an aftermarket imitation. It is sourced directly from original equipment manufacturer for use with electric air compressors. It is connected to a standard US outlet to supply power to the unit. Please note, this rubber insulated power cord is sold individually. You will need a screwdriver to replace this item.
WHEEL 9 BLACK SEMI-P – Part Number: D23138
No Longer Available
WHEEL 9 BLACK SEMI-P
Part #D23138
This wheel is a genuine OEM replacement part used in portable air compressors. It consists of a plastic rim and rubber tire with an outer diameter of 9.5 inches. It is held in place on the compressor axle by a shoulder bolt and nut. The wheel allows the equipment to move smoothly during use. If the tire is punctured, or the rim is damaged, the wheel will need to be replaced to restore the portability of your equipment. If the nut and bolt are worn down, it is recommended to replace them at the same time. Remove the nut and bolt that secure the wheel and pull it off the axle. Place the new wheel in position and secure it with the fasteners (sold separately). Each wheel is sold individually.
TUBE SEAL – Part Number: N044359
$6.40
Special Order
TUBE SEAL
Part #N044359
This replacement tube seal is a high quality item that is supplied by original equipment manufacturer for use with Craftsman air compressors. It is placed on the outlet tube coming from the head of the compressor. Please note this durable rubber tube seal is sold individually.
CLAMP HOSE .250 ID – Part Number: CAC-1206-1
$6.40
In Stock
CLAMP HOSE .250 ID
Part #CAC-1206-1
Genuine OEM replacement part, this item is sold individually. This part is used in various places in the compressors listed below. By its part name, it is used to clamp hoses onto certain parts on the compressors.
ASSY FASTENER – Part Number: ACG-408
$6.40
In Stock
ASSY FASTENER
Part #ACG-408
This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individually. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.
VALVE PLATE ASSY – Part Number: N017592SV
$22.71
In Stock
VALVE PLATE ASSY
Part #N017592SV
Genuine Porter Cable replacement part, this item is sold individually. Head Gasket Sold Separately. This part is used in the all of the compressors models listed below. When air is pumped by the piston it passes through the Valve Plate into the compressor tank. There are reeds on the valve plate that will eventually wear out, and the Valve plate will need to be replace. It is advisable at this time to replace the Graphite Gasket Kit, part number D30139.
BELT TIMING – Part Number: AC-0815
$32.37
In Stock
BELT TIMING
Part #AC-0815
This is an OEM part sourced directly from the manufacturer. The belt is commonly found in Craftsman air compressors. This part is made of flexible rubber, and is used to transfer power between the piston and the pump assembly. Over time, it may become cracked and brittle, requiring replacement. You may need an Allen wrench or hex key when replacing this part. This item is sold individually.
HOSE – Part Number: H-7051
$6.40
In Stock
HOSE
Part #H-7051
This is a genuine manufacturer approved replacement part designed for use with air compressors. This is the hose that delivers air from the tank. It is made out of rubber and it is sold individually. Please note the hose clamps are sold separately.
Valve – Part Number: D20114
$10.70
In Stock
Valve
Part #D20114
This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions, and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by tension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. This safety valve has a thread sealant pre-applied, so additional thread sealant is not required, the safety valve is sold individually.
NUT PACK – Part Number: SSP-473
$6.40
In Stock
NUT PACK
Part #SSP-473
This is an OEM part sourced directly from the manufacturer. The nut sleeve is designed for use in Craftsman air compressors. This part is made of metal, and is generally used in securing the check valve. You may require a wrench when replacing this part. This item is sold individually.
Connecting Rod Assembly – Part Number: N036518
$55.07
In Stock
Connecting Rod Assembly
★★★★★
★★★★★
(1)
Part #N036518
This replacement piston kit is designed for use with select air compressors and includes everything you need to restore smooth, efficient operation. The kit comes with a piston rod, compression ring, cylinder sleeve, and bearing—all made from durable materials for long-lasting performance. These components work together to maintain proper compression and airflow inside the unit. Please note that this kit does not include the valve plate, head gaskets, or other compressor parts. To install, you’ll need a screwdriver, hex key (Allen wrench), and pliers. Replacing worn or damaged internal parts can help improve your compressor’s performance and extend its service life. This kit is sold individually and is ideal for routine maintenance or repair.

Common Symptoms of the Y6020-WK

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Worn piston rod and sleeve
7 of 12 people found this instruction helpful.
  • Donald from BRYAN, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Disassemble plastic housing around compressor unit using appropriate tools. Remove the four bolts from the compressor head using a 5/16 nut driver. Carefully remove head assembly including airline. Remove bolt through rod bearing with Allen wrench.

Reassemble with new rod and piston assembly. Best to use blue locktite on bolt through rod bearing when reassembling. Make sure to torque all bolts to specs listed.
Was this helpful?
Thank you for voting!
Can't find this special screw used on many housings etc
4 of 6 people found this instruction helpful.
  • Tim from Tucson, AZ
  • Very Easy
  • 15 - 30 mins
Actually don't like using Torx bits because they are hard to center deep in the channel. I had misplaced these forcing me to order replacements.
My plan is to insert Torx bits before screwing in and using jb weld to secure the bit to the screw, giving me a hex head. Can't find this special screw with a hex head. This screw is called AGC-408 by craftsman.
Was this helpful?
Thank you for voting!
Broken ground on original plug
2 of 2 people found this instruction helpful.
  • Debra from PRESCOTT VLY, AZ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed cover & old cord.
Replaced with new cord & replaced cover.
Works perfect.
Was this helpful?
Thank you for voting!