EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

XRS18GGABWW General Electric Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Evaporator Fan Motor – Part Number: WR60X31522
$75.13
In Stock
Evaporator Fan Motor
★★★★★
★★★★★
(153)
Part #WR60X31522
This 115-volt 60Hz evaporator fan motor is located in the back of the freezer and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. If the motor has failed, the freezer/refrigerator will become too warm because the fan motor is not circulating the cool air from the freezer into the refrigerator. This is a genuine OEM part. Please remember to disconnect the power to the appliance before starting your repair.
Glass Shelf – Part Number: WR32X21260
$39.46
In Stock
Glass Shelf
★★★★★
★★★★★
(104)
Part #WR32X21260
This glass shelf is a genuine OEM replacement part is specially designed for refrigerators. It has a length of approximately 23 inches and a width of 13.5 inches. The glass shelf provides a wide surface for you to store various food items and containers inside your refrigerator. It is designed to easily slide in and out of the fridge as needed. If your glass shelf is cracked or damaged it is recommended to replace it promptly for your safety. No mounting hardware is needed, simply pull out the damaged glass shelf and position the new one its place.
REFRIGERATOR DOOR LIGHT SWITCH – Part Number: WR23X31507
$18.37
In Stock
REFRIGERATOR DOOR LIGHT SWITCH
★★★★★
★★★★★
(41)
Part #WR23X31507
This is the light switch that goes in your refrigerator. If the light is not working or stays on, you may need to replace the switch. It is made of mainly white plastic, and is an OEM part, directly from the manufacturer. Be sure to disconnect the refrigerator from the power source before you begin this repair. To remove the switch, simply use a flathead screwdriver to pop the switch out from the refrigerator wall, then disconnect the wires. Reconnect the wires to the new switch, snap it into place, and the repair is complete.
BLADE EVAP FAN ASM – Part Number: WR60X46086
$29.32
In Stock
BLADE EVAP FAN ASM
★★★★★
★★★★★
(8)
Part #WR60X46086
This blade attaches to the evaporator motor.
Lid Bumper – Part Number: WR02X10540
$16.05
In Stock
Lid Bumper
★★★★★
★★★★★
(2)
Part #WR02X10540
The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down or missing, and the sound could be a result of the motor scraping the side bracket. You will find it between the fan motor and the side bracket on the evaporator fan motor assembly. To access the bumper, you will need to remove the evaporator fan motor assembly from the freezer. This part is made of orange rubber and is less than half an inch in diameter. It has a rounded top and a slightly pointed bottom, and is sold individually.
FRESH FOOD SHELF – Part Number: WR17X30024
$30.41
In Stock
FRESH FOOD SHELF
★★★★★
★★★★★
(13)
Part #WR17X30024
The door shelf rail snaps into place on the door to hold items on the door shelf.
Condenser Fans Blade Assembly – Part Number: WR60X10207
$19.40
Special Order
Condenser Fans Blade Assembly
★★★★★
★★★★★
(2)
Part #WR60X10207
The condenser fan blade assembly helps to regulate the temperature in your refrigerator or freezer. This fan assembly has 4 blades, but other fans may have 3 blades, so be sure to check the number of blades on your fan. The fan blade is made of white plastic and is approximately 6 inches in diameter. If your freezer section is too warm, or you notice a strange noise coming from your refrigerator when it is running, you may need to replace the condenser fan blade assembly. This part is sold individually.
Door Hinge Nylon Washer – Part Number: WR01X27364
$16.05
In Stock
Door Hinge Nylon Washer
★★★★★
★★★★★
(2)
Part #WR01X27364
This is the replacement hinge washer for your refrigerator. The hinge washer is mounted on the top of the door hinge pin, and supports the refrigerator door, allowing it to open and close easily. The main reason you would need to replace the hinge washer is if it is worn out, causing the refrigerator door to be more difficult to open and close. You may also hear an unpleasant noise when you open your refrigerator door. The washer is a little less than an inch in diameter and is sold individually. This is an authentic OEM part sourced directly from the manufacturer.
Refrigerator Crisper Drawer – Part Number: WR02X31766
$59.16
In Stock
Refrigerator Crisper Drawer
★★★★★
★★★★★
(7)
Part #WR02X31766
This crisper drawer is for refrigerators. Crisper drawer stores fruits and vegetables at a humidity level that helps keep them fresh longer. Follow the instructions in the owner's manual when installing this part.
Refrigerator Hinge Bottom Pin – Part Number: WR02X27092
$16.23
In Stock
Screw – Part Number: WR01X21151
$16.05
In Stock
Screw
Part #WR01X21151
Refrigerator Freezer Door Gasket – Part Number: WR14X27230
$74.75
Special Order
Refrigerator Freezer Door Gasket
★★★★★
★★★★★
(12)
Part #WR14X27230
The freezer door gasket creates a seal around the door to prevent warm air from entering the freezer compartment.

Common Symptoms of the XRS18GGABWW

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer Fan
267 of 302 people found this instruction helpful.
  • Luis from College Station, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I removed two srews from the back panel inside fthe reezer compartment and the two that hold the air manifold/baffle? and pulled the baffle out. Then, I removed the two srews that hold the front part of the fan bracket behind the baffle and the back panel came out easily. Two more screws and one quick connect plug attached to the fan and I was done with removal. Insallation was even quicker, I slid the original fan right off the old motor and slid it on the new motor's shaft. Piece of cake! Thanks Partselect.
Was this helpful?
Thank you for voting!
dropped something on the light switch and it broke off
61 of 70 people found this instruction helpful.
  • Lorinda from Dallas, TX
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
we just pried out the old switch and pulled it out the rest of the way with a pair of needle nose pliers. Pulled off the wires on the broken switch and reattached to the new one and just slid/clicked it back into the hole.
Was this helpful?
Thank you for voting!
Loud Fan Motor
54 of 65 people found this instruction helpful.
  • Arthur from East Meadow, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Unplug refrigerator.Remove the floor of the freezer box by removing the 4 philips head screws. Remove the cover over the fan by pulling it straight up and out. Remove the styrafoam duct by pulling it straight up and out. Remove the back wall of the freezer by removing the 4 philips head screws. Unplug fan. Remove the fan, bracket and all, by removing the two philips head screws on the back wall. Take the two halves of the bracket appart by removing the two hex head scews on the back of the bracket. Remove the "O" ring from the fan blade and remove the blade. There is a rubber grommet on both the front and back halves of the bracket. Make sure they are set properly in the brackets to secure and position the motor properly so the fan blade doesn't hit anything when it spins. Install the new motor onto the bracket the same way you took the old one off. Check the positions of the brackets, rubber grommets and motor to make sure they're properly installed and secure. Replace the "O" ring onto the fan blade and install it onto the new motor with a firm push on the center of the blade. Install the brackets and fan onto the back wall and plug in the new motor. Reinstall the back wall of the freezer box and make sure the motor is secure. Plug the refrigerator back in and check to make sure the fan blade doesn't hit anything while it's turning. Finish reassembling the freezer box.
Was this helpful?
Thank you for voting!