Models
>
WWA8072BAL
WWA8072BAL General Electric Washer - Overview
Sections of the WWA8072BAL
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
D-Shaped Knob Clip
PartSelect #: PS268493
Manufacturer #: WH01X10106
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
No Longer Available
Timer Knob with Clip
PartSelect #: PS271127
Manufacturer #: WH1X2757
This part is the replacement timer knob for your washer. It is made of white plastic and is about 1 ¼ inches in diameter. The timer knob sits on the timer shaft and allows you to choose the wash cycle...
No Longer Available
Compression Ring
PartSelect #: PS271609
Manufacturer #: WH2X650
This compression ring works in conjunction with the timer dial.
No Longer Available
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$12.22
In Stock
Four Port Pump
PartSelect #: PS271344
Manufacturer #: WH23X42
This washing machine pump is white in color and has four ports for water to pass through.
No Longer Available
Agitator Coupling
PartSelect #: PS270786
Manufacturer #: WH1X1944
This coupling is used for 20 spline drive shaft transmissions.
No Longer Available
Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$15.89
In Stock
Friction Snubber Pad
PartSelect #: PS270875
Manufacturer #: WH1X2296
This friction snubber pad is an inch and a half long.
No Longer Available
Lower Shaft Seal
PartSelect #: PS273876
Manufacturer #: WH8X281
This seal goes to bottom of the transmission to stop oil from leaking at the bottom of the appliance.
No Longer Available
Questions And Answers for WWA8072BAL
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WWA8072BAL
[Viewing 4 of 4]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced the Agitator coupling
First, you will need to remove the agitator, if it hasn't fallen off by itself. Than, you will need a pulley to remove the coupling from the spinning pole . I used one of those pulleys with three arms to remove it , Second, I lubricated the inside of the new coupling with a little oil, and sided it down on the spinning pole. It was
... Read more
a little hard to installed but, I used a hammer and tapped it in. Third, I also put some lubricant on the new coupling to help the agitator slide down a little easier on the new coupling.
P.S. Check inside agitator for old rubber of the old coupling and remove it. (only if it has fallen off the old coupling.)
P.S. Check inside agitator for old rubber of the old coupling and remove it. (only if it has fallen off the old coupling.)
Read less
Parts Used:
-
jose from lAREDO, TX
-
Difficulty Level:Difficult
-
Total Repair Time:15 - 30 mins
49 of 60 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old water pump was leaking, needed replacment
## WHAT I WISH I'D KNOWN BEFORE I STARTED ##
1. Remove the four hoses first.
2. remove the three screws holding the pump to the structure above BEFORE loosening the flex clamp.
3. with the pump free of the hoses and rest of the washer, then remove the flex coupling clamp from the pump end only; do not remove the flex coupli ... Read more ng from the motor.
4. remove the old pump.
5. attach the new pump to the top of the flex coupling BEFORE attaching the pump to the upper part of the washer. This is the most difficult step, to get the flex coupling on the pump in a secure fashion using the clamp. It's much easier to do if the pump is not yet connected to the rest of the washer.
6. attach the pump to the washer with the three mounting screws.
7. re-attach the hoses.
8. run the washer and check for leaks.
I made the mistake of taking the flex coupling off the motor then tried to put the flex coupling on the motor and the pump when the pump was already attached to the washer. Major grief :>(
Good luck, it's well worth the effort.
1. Remove the four hoses first.
2. remove the three screws holding the pump to the structure above BEFORE loosening the flex clamp.
3. with the pump free of the hoses and rest of the washer, then remove the flex coupling clamp from the pump end only; do not remove the flex coupli ... Read more ng from the motor.
4. remove the old pump.
5. attach the new pump to the top of the flex coupling BEFORE attaching the pump to the upper part of the washer. This is the most difficult step, to get the flex coupling on the pump in a secure fashion using the clamp. It's much easier to do if the pump is not yet connected to the rest of the washer.
6. attach the pump to the washer with the three mounting screws.
7. re-attach the hoses.
8. run the washer and check for leaks.
I made the mistake of taking the flex coupling off the motor then tried to put the flex coupling on the motor and the pump when the pump was already attached to the washer. Major grief :>(
Good luck, it's well worth the effort.
Read less
Parts Used:
-
LLOYD from Moffett Field, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
44 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lost all gear oil bottom of transmission
put washer on its side,removed 1cross section,loosened the nut that held on the pulley.
loosened the motor and removed drive belt,removed drive pulley,removed old seal,poured in 90 weight gear oil,installed new seal and done everything else in reverse order.
stood washer upright connected water hoeses,waste water discharge hose, ... Read more set washer to spinanr turned it on to make sure no more leaks.
everything is working well
loosened the motor and removed drive belt,removed drive pulley,removed old seal,poured in 90 weight gear oil,installed new seal and done everything else in reverse order.
stood washer upright connected water hoeses,waste water discharge hose, ... Read more set washer to spinanr turned it on to make sure no more leaks.
everything is working well
Read less
Parts Used:
-
opal from richmond, KS
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set, Wrench set
28 of 31 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!