Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WW27430BC > Instructions

WW27430BC Jenn-Air Wall Oven - Instructions

All installation instructions for WW27430BC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WW27430BC
121-135 of 210
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace cracked glass.

  • Customer: George from Interlochen, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 13 people found this instruction helpful
Pulled oven door out of oven and and replaced glass.

Clock time display was very faded, barely visible and when the oven temperature and/or timer were activated, the entire display was not visible. User had to guess the temperature and time.

  • Customer: Terry from Spicewood, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First we disconnected power to the oven. Then we removed the two screws that attached the oven control panel cover to the body of the oven. Next we removed the screws that secured the faulty clock assembly to the control panel. Then we un-installed the three cable/connectors. The two wire cable/connectors were simple pull-outs. But with no instructions in either the Users Manual or shipped with the replacement part, we had no idea how to un-install the ribbon cable. Fifteen minutes later, much trial and error, and simple blind luck, we finally realized that we simply had to lift up the connector ears and the ribbon cable would disengage. Then it was a simple matter of seating the replacement assembly, installing the two screws, re-installing the three cables, reseating the control panel cover and re-installing the cover screws. Once power was restored to the oven, the clock was reset. We tested the oven temperature and the timer. All was well once again.
Question: Would you like us to return the faulty Jenn-Air part for trouble-shooting?
Recommendation for the future: Send some simple installation instructions. We both have computer manufacturing asembling experience but never worked with a ribbon cable connector like this one. That connector was a major stumbling block for us. A simple changeout turned into a 30+ battle.
But, I would like to thank you for the quick shipment of this part. It was ordered on a Monday and received in Wednesday's mail. That so FAST! and very much appreciated.
Your website is now in my Favorites and in my email address book. Thank you once again for all your help.
Sharon Hall
133 Lake View Drive
Spicewood, TX 78669
830 693-4513
thumper@tstar.net

clock did not light up

  • Customer: Clarence from Easton, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
i did it myself

The bake element got so hot it caught fire! The electrical type

  • Customer: Brandie from Nashville, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We cut the electricity to the stove at the breaker box. We had to do that to keep the fire from spreading in the first place. We took 2 screws out and used the same screws to install the new bake element. It was just 2 connectors that had to be pulled apart gently from the old bake element. We plugged in the new bake element into the metal spaces where the old one came out. Replaced the screws and we were done. It was very easy.

Oven door was locked, couldn't set oven temps

  • Customer: William from Nashville, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

Light bulb failure

  • Customer: Grant from Alexandria, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Oven would not turn on

  • Customer: Stacey from Tampa, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.

Element cracked and not heating

  • Customer: Rebecca from bethlehem, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old element attached connections to new element tightened screws to install

door wouldn't close well for 3rd time

  • Customer: Barbara from Reno, NV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had repair men replace the door hinges 2times and decided the 3rd time to do it myself and save some $. ordering was a chinch, received the parts in 2 days and followed instructions posted on this site. They were excellent. Just a few things I would stress: Lift UP the door to remove, not open the door fully and pull out and also make sure to take the small pins out of the new hinges before closing. They are so small you could over look them. The person who put detailed instructions on this site is to be commended for clarity and detail on "How To" I really appreciated it.

temperature varied in oven.couldn't set

  • Customer: tom from winter haven, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

Heating Element Burned Out

  • Customer: Walter from Manassas, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Friday, 16 November, the oven heating element has burned out. Thanksgiving is the 22nd. The turkey awaits. Panic reigns.
I call Sears for repair. An appointment is set for Sunday the 18th between noon and 5 pm. An email confirms the appointment. On Saturday a telephone call confirms the appointment. On Sunday at 4:30 no repairman has appeared and no phone call has been received. I check the computer. An email from Sears states the repairman had called but nobody was home. Please call to schedule another appointment. I call Sears and tell them there were five people here all day, I have two doorbells and a dog that barks. Sears says they never schedule repairs on Sunday. Another appointment can’t be made till after Thanksgiving. So much for Sears repairs.
My son says he can fix the oven if I can get the heating element. Monday morning the local hardware says they can’t get an element till after Thanksgiving and send me to Maytag. Maytag says the can get an element by Tuesday and so I order but don’t have faith.
I discover xxx on line. I call the number and a nice lady in Nova Scotia answers. She assures me she can have the element here by Tuesday morning. Again I order but don’t have faith.
Tuesday morning the element arrives. We’re saved. Tuesday afternoon Maytag calls and we’re saved again.
My experience with xxx is nothing but fantastic. I highly recommend you service. And I learned they do celebrate Thanksgiving in Canada but on a different date.
Thank you!

Top oven sensor

  • Customer: Alan from Bonita, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

Long Oven Sensor failure - oven over heated & shut down

  • Customer: JAMES from SEATTLE, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

oven not staying on. fault cod F-3 showing

  • Customer: James from Cumberland, MD
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.

Element in oven would not adjust to the oven temperature.

  • Customer: Dolores from Edmond, OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.
All Instructions for the WW27430BC
121-135 of 210