This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This lid lock assembly is supplied by the original manufacturer for use in various models of top-load washing machines. The assembly includes the lid lock mechanism and the wiring harness. You can find it positioned on the underside of the washer lid. The lid lock assembly is designed to prevent the washer lid from opening during use. Thi...Read mores is a safety mechanism that ensures that users do not accidentally come in contact with moving parts or are not injured by spilled water or detergent. If the lid lock assembly is faulty, the washer may be unable to start the cycle or it may stop in the middle of a cycle.
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Affresh Washing Machine Cleaner includes three slow-dissolving tablets that help remove odor-causing residue from inside the washer. Suitable for all washer brands, including high-efficiency (HE) machines, the formula is also septic-safe. Place one tablet directly in the empty wash basket and run the Clean Washer cycle, or use a normal cycle with hot water. Use monthly or every 30 wash cycles for best results.
This is a water inlet valve made for washing machines. This part is used to control the flow of water into the fill hose of the washing machine, to allow the washer to fill up with water. If your washing machine is not filling up with water properly, or if you are noticing leaks underneath your washing machine, the inlet valve has likely ...Read morefailed and you will likely need to replace it. This OEM inlet valve features two different inlets for hot and cold water but does not come with any other parts or accessories for installation. To replace this water inlet valve, you will need tools such as a screwdriver or wrench to gain access to it and remove it.
This is an impact absorber, also known as a sound dampening pad, for washing machines. This sound dampening pad attaches to the top of your washing machine drum to reduce the severity and harshness of vibrations and movement during the washing and spinning cycle, to produce a quieter laundry experience. If your washer is shaking excessive...Read morely during operation, this pad may be worn out or simply missing, and in need of replacement. To replace this pad, you will need a screwdriver or wrench to access the inner portion of your washing machine and remove the old one and install the new one. This OEM pad measures 5-inches by 3-inches and is sold individually.
This clutch slider kit is genuine OEM replacement kit that fits in various models of washing machine. It is a part of the transmission system in your washer which is responsible for controlling the movement of the agitator during the wash and spin cycles. The assembly includes the clutch band, slider, and lock ring. The kit helps to regul...Read moreate the speed and direction of the agitator or drum. It allows the machine to start and stop spinning smoothly, as well as change speeds as needed during the wash and spin cycles. If the clutch slider kit has worn or damaged components, it can lead to problems like difficulty starting or stopping the machine, excessive noise during operation, or failure to spin properly.
This drain pump is specially designed to fit in top load washing machines. It is responsible for removing water from the washer tub during the drain cycle and directing it to the household plumbing system through the drain hose. If you notice longer draining times, grinding or rattling sounds, or standing water in the tub at the end of a ...Read morecycle, the drain pump is likely faulty. This may be due to several reasons such as normal aging, wiring problems or physical damage. It is also common for the drain pump to become clogged with small items such as coins or buttons.
This lid hinge is a genuine OEM replacement part for your washing machine. This hinge is for the left side of your lid, although it is a good idea to replace btoh hinges at once. The hinge holds up the washing machine lid and can become rusted over time. This repair is rated easy by our customers.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael - For model number WTW8040DW4
February 16, 2020
The lid periodically will not lock causing the washer cycle to not start. I will hold the start button a few times and eventually it will indicate locked and work. We have had the washer for less than a year and have had no problems until now. It started a week ago and has happened more often.
Hello Michael,
Thank you for your question. Our sources suggest replacing the lid lock assembly under part PS11722981 for your model to fix the issues with the washer lock. We hope this helps.
Hello Terry, thank you for getting in touch. You can simply check whether the drain pump, part number PS11738156, of your model is draining the water or not. If it is not draining, you can visually inspect the drain pump for any blockages or damages. If the problem persists, then you may need to test it using a multimeter for continuity. If the drain pump is found at fault, then it may need to be replaced. We hope this information helps!
I have constant dripping from the softener detergent tray. I left for 11 days and the washer filled up. I had unplugged it as the pump was kicking on and running for 15-20 minutes
Hello Donald, Thank you for the question. Normally this is an indication the Water Inlet Valve is faulty and will need to be replaced. Thank you for your inquiry, good luck with this repair!
Cambrio whirlpool washer fills with water then just sits there, does nothing else! Help!
Hi Kathryn, thank you for reaching out. According to our research, you need to check the following parts: water pressure hose, part number PS11741846, lid lock assembly, part number PS11722981, wash plate, part number PS11699797, and gearcase, part number PS12741641. Please contact us anytime if you require further assistance!
Hi Jim, thank you for the great question. Your washer may be facing this issue because of the faulty water inlet valve, part number PS12349461. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud grinding noise when the washer was in use.
69 of 84 peoplefound this instruction helpful.
Charles from STARKVILLE, MS
Easy
1- 2 hours
Nutdriver, Screw drivers, Socket set
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate
... Read more( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
Read less
Was this helpful?
Thank you for voting!
Washer making noise on spin cycle
20 of 29 peoplefound this instruction helpful.
Roy from MAYNARDVILLE, TN
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers
Removed two screws on back of lid to raise top removed tub one bolt and one spanernut pulled tub lowered top reinstalled screws laid washer down to get to bottom of washer unplugged wiring removed four bolts pulled gear box and motor removed motor from gear box installed motor on new gear box reassemble washer
Was this helpful?
Thank you for voting!
Replace Cracked Whirlpool Cabrio Washing Machine Lid
14 of 14 peoplefound this instruction helpful.
Jonathan from HELENA, AL
Very Easy
Less than 15 mins
Screw drivers
This is a very simple repair. My lid was severely cracked on the back left corner where there seems to be a lot of pressure/torque required to shut the lid. There is a metal L-shaped "tab" that inserts into the lid on both sides of the back edge of the lid. The lid is attached to these metal tabs with two screws for each side. My crack
... Read moreed lid had resulted in the lid breaking off of the metal tab with the screws still anchored into the metal tab.
Make sure screws have been removed from the metal tabs on both sides. Do not remove metal tabs- leave them attached to the washing maching (otherwise, you will not be able to attach the lid back onto the machine). Slide the lid over the tabs. There are square-shaped spaces along the edge of the lid where the tabs slide into the lid. Re-screw the screws into the lid, attaching the lid to the tabs through pre-drilled holes on the sides of the lid. It may take a little time to make sure the screws are properly inserted into the lid and tab screw holes. Tighten up and you're finished.
My Orders
