Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This washer drain pump assembly is a genuine OEM replacement designed to expel water from the washing machine during the drain and spin cycles. Engineered for compatibility with a wide range of models...
This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This washer lid lock assembly is designed to ensure safe and efficient operation of top-loading washing machines by securely locking the lid during wash and spin cycles. It prevents the machine from r...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
This is a replacement lid hinge for your washer. It is approximately 2.5 inches in length and 1.5 inches in width. The lid hinge is what the lid for your washer pivots on. If the lid hinge is damaged,...
This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To c...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Charlotte T.
January 18, 2020
How to remove agitator
For model number WTW7600XW2
Hello and thank you for writing.
Lift the lid on your washer to expose the agitator. Pull the fabric soften dispenser from the top of the agitator. Insert the socket into the agitator to remove the agitator bolt from inside the agitator. Reach your fingers beneath the agitator and lift it from the machine. We hope this helps. Please contact us anytime if you require further assistance.
2 people found this helpful.
Did this question help you?
Thank you for voting!
Carlos
March 20, 2022
Hola, mi lavadora no saco el agua y aparece este código f32, cual será el problema? Gracias
For model number WTW7600XW2
Hola Carlos, gracias por la pregunta. El código de error F32 es un código de falla del interruptor de presión de nivel de agua. Sugerimos revisar la manguera de presión de agua en busca de obstrucciones o acumulaciones. Si está claro, será necesario reemplazar el tablero de control ya que el interruptor de presión es parte del tablero para este modelo. Si necesita ayuda para realizar un pedido, el servicio de atención al cliente está abierto los 7 días de la semana. No dude en llamarnos. ¡Esperamos con interés escuchar de usted!
What capacity is this washer? It is now starting to leak water from underneath, and what is the possible cause. I checked the hoses, and they are okay.
For model number WTW7600XW2
Hello Jim, thank you for reaching out. According to our research, the capacity of your washer is four cubic feet. Checking out the drain pump, part number PS5136124, may help you get to the root of the problem. We hope this information helps!
Looking for a wire harness that goes from the top control board down to the control panel I believe you call it. It has like 6 white wires and 1 black wire, it's about 18 inches long. Was wondering if that is available. Thank you.
For model number WTW7600XW2
Hello Kenneth, thank you for getting in touch. According to our research, the wire harness you are looking for is part number PS11752947. The wire colors may not be exactly like the one you are replacing, but it will work as its replacement. We hope this helps.
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.
Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover
... Read moreover the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.
At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).
Re-assemble using new pump.
Note: Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring cla
... Read moremps, unhooked the wiring( its a single plug in) and reverse the procedure for installing.
I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.
I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.
Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitratin
... Read moreg oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great
