This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Order within the next 4 hrs and your part ships today!
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Order within the next 4 hrs and your part ships today!
This lid lock assembly is supplied by the original manufacturer for use in various models of top-load washing machines. The assembly includes the lid lock mechanism and the wiring harness. You can fin...
$143.75
In Stock
Order within the next 4 hrs and your part ships today!
This is a replacement lid hinge for your washer. It is approximately 2.5 inches in length and 1.5 inches in width. The lid hinge is what the lid for your washer pivots on. If the lid hinge is damaged,...
$8.00
In Stock
Order within the next 4 hrs and your part ships today!
This is a water inlet valve made for washing machines. This part is used to control the flow of water into the fill hose of the washing machine, to allow the washer to fill up with water. If your wash...
$92.13
In Stock
Order within the next 4 hrs and your part ships today!
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Order within the next 4 hrs and your part ships today!
Order within the next 4 hrs and your part ships today!
Questions And Answers for WTW7000DW3
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Maxwell
March 24, 2020
Does the washer wtw7000dw3 has a manufacturer`s warranty.? the gear case went out. this is my second cabrio in 4 years because of problems. thank you.
For model number WTW7000DW3
Hello Maxwell,
Thank you for your question. We believe this is a concern best addressed by the manufacturer. We are a parts distributor. We do not manufacture any units, provide technical support, authorize substitutes, fulfill warranty claims, or have access to dimensions for entire models. Please contact your unit's manufacturer, directly. We hope this helps.
3 people found this helpful.
Was this helpful?
Thank you for voting!
William
December 28, 2019
How much for control panel
For model number WTW7000DW3
Hi William, the control panel is linked below. Clicking on this part will give you the current pricing. Thank you for your question and good luck with your repair!
This is the lid lock for my whilrpool washing machine model number, wtw7000dw3.Or if there is another part# compatible with it
For model number WTW7000DW3
Hello Jonathan, thank you for writing. The replacement Lid Lock Assembly for your model is part number PS11722981. Good luck with your repair!
Was this helpful?
Thank you for voting!
Trish
June 14, 2021
My Maytag washing machine is leaking water any suggestions? I am calling a repair person, but would like to know approximately what I am looking at for repair bills
For model number WTW7000DW3
Hello Trish, Thank you for the question. With a washer a leak can be caused by a few different parts. We suggest starting by checking the hoses for damage and to make sure they are secure. You can also check the Drain pump for clogs or damage that can cause a leak as well. Check the drum for cracks or if the leak is coming from the center at the bottom were the Drum Seal is located. We hope this helps.
Hi Ron, thank you for contacting us. Based on our research, the issue is with the clutch, part number PS10064562. It spins the basket during the spin cycle. We would recommend checking the clutch to fix the issue. We hope this solves your problem!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate
... Read more( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
