WTW6600SW2 Whirlpool Washer Parts & Repair Help | PartSelect
Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WTW6600SW2

WTW6600SW2 Whirlpool Washer - Overview

Get Parts and Repair Help for WTW6600SW2

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(14)
PartSelect #:PS5136124
Manufacturer #:W10536347
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$106.79
In Stock
(1)
PartSelect #:PS11743008
Manufacturer #:WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...
$4.92
In Stock
(11)
PartSelect #:PS11723155
Manufacturer #:W10820039
This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need ...
$24.04
In Stock
(1)
PartSelect #:PS11742721
Manufacturer #:WP488729
This metallic screw is less than an inch long and comes with a plastic washer.
$4.90
In Stock
(11)
PartSelect #:PS11756782
Manufacturer #:WPW10619844
This part makes sure that the lid is shut before allowing the machine to start or agitate. NOTE: This is a manufacturer substitution. Part may differ in appearance but is a functio...
$73.79
In Stock
(1)
PartSelect #:PS11740613
Manufacturer #:WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...
$6.02
In Stock
PartSelect #:PS385132
Manufacturer #:72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...
$7.20
In Stock
(12)
PartSelect #:PS11723157
Manufacturer #:W10820048
The suspension rod kit supports the wash drum and keeps it stable during unbalanced loads. If your washer is making a loud banging sound during the washing cycle, check to ensure t...
$78.21
In Stock
PartSelect #:PS347819
Manufacturer #:350930
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is...
$10.36
In Stock
(3)
PartSelect #:PS11746820
Manufacturer #:WP89503
This hose can handle hot or cold water and is five feet long.
$8.51
In Stock
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loose change entered drain pump, cracked housing leaked all water out

Drain Pump – Part Number: W10536347
  • Customer: ROBERT from BARRINGTON, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 196 of 224 people found this instruction helpful
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.

Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover over the outer and i... read more

Washer always stopped at the 47th and 24th minute of each load and display F1 error code. I would have to press "cancel" and then "start" a few times for it to continue.

  • Customer: James from Turnersville, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 147 of 167 people found this instruction helpful
Removed the dial control top covering by unscrewing the 3 screws in the back of the cover. Once the cover was off, the control module was exposed and all I had to do was:

1. Disconnect the wires that were plugged into the control module

2. Remove the old module. There was 1 screw holding it in place.

3. Replace with the new... read more

Water pump for draining

Drain Pump – Part Number: W10536347
  • Customer: Kerry from Alleyton, tX, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 59 of 71 people found this instruction helpful
The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring clamps, unhooked the wi... read more